Bacula-users

Re: [Bacula-users] new bacula installation

2010-08-13 10:23:05
Subject: Re: [Bacula-users] new bacula installation
From: jeffrey Lang <jrlang AT uwyo DOT edu>
To: Richard Scobie <richard AT sauce.co DOT nz>
Date: Fri, 13 Aug 2010 07:59:21 -0600
Again  use "lsscsi -g" to get detailed and direct information about your devices.  Below is the output for my system

[root@bkupsvr2 ~]# lsscsi -g
[0:0:0:0]    disk    ATA      WDC WD3000HLFS-0 04.0  /dev/sda  /dev/sg0
[1:0:0:0]    disk    ATA      WDC WD3000HLFS-0 04.0  /dev/sdb  /dev/sg1
[5:0:0:0]    cd/dvd  HL-DT-ST DVDRAM GT20N     CQ02  /dev/scd0  /dev/sg2
[6:0:0:0]    tape    HP       Ultrium 5-SCSI   I21H  /dev/st0  /dev/sg3
[6:0:1:2]    tape    HP       Ultrium 4-SCSI   B45H  /dev/st1  /dev/sg4
[6:0:1:4]    tape    HP       Ultrium 4-SCSI   B45H  /dev/st2  /dev/sg5
[6:0:1:6]    tape    HP       Ultrium 4-SCSI   B45H  /dev/st3  /dev/sg6
[6:0:1:8]    tape    HP       Ultrium 4-SCSI   B45H  /dev/st4  /dev/sg7
[6:0:1:10]   tape    HP       Ultrium 4-SCSI   B45H  /dev/st5  /dev/sg8
[7:0:0:0]    tape    HP       Ultrium 5-SCSI   I21H  /dev/st6  /dev/sg9
[8:0:0:0]    tape    HP       Ultrium 5-SCSI   I21H  /dev/st7  /dev/sg10
[8:0:0:1]    mediumx OVERLAND NEO Series       0122  -         /dev/sg11
[8:0:1:0]    mediumx OVERLAND REO Series       0425  -         /dev/sg12
[8:0:1:1]    tape    HP       Ultrium 4-SCSI   B45H  /dev/st8  /dev/sg13
[8:0:1:3]    tape    HP       Ultrium 4-SCSI   B45H  /dev/st9  /dev/sg14
[8:0:1:5]    tape    HP       Ultrium 4-SCSI   B45H  /dev/st10  /dev/sg15
[8:0:1:7]    tape    HP       Ultrium 4-SCSI   B45H  /dev/st11  /dev/sg16
[8:0:1:9]    tape    HP       Ultrium 4-SCSI   B45H  /dev/st12  /dev/sg17
[9:0:0:0]    tape    HP       Ultrium 5-SCSI   I21H  /dev/st13  /dev/sg18


Richard Scobie wrote:
Jeremiah D. Jester wrote:
  
I'm confused. The tapeinfo output for /dev/sg1 says it is a 'Tape Drive' and of type 'TD4' or LT04, the new supported capacity. Sg0 is the hard drive. I get no output for devices sg3-sg10.  Please explain.
    
What is the output of:

cat /proc/scsi/sg/device_strs

On my sd machine with attached HP changer, I get:

ATA             WDC WD2002FYPS-0        04.0
ATA             WDC WD2002FYPS-0        04.0
ATA             WDC WD2002FYPS-0        04.0
ATA             WDC WD2002FYPS-0        04.0
ATA             WDC WD2002FYPS-0        04.0
ATA             WDC WD2002FYPS-0        04.0
ATA             WDC WD3202ABYS-0        02.0
ATA             WDC WD3202ABYS-0        02.0
ATA             WDC WD2002FYPS-0        04.0
ATA             WDC WD2002FYPS-0        04.0
HP              Ultrium 4-SCSI          B56W
HP              MSL G3 Series           4.70

This shows the changer component is /dev/sg11.

Regards,

Richard

------------------------------------------------------------------------------
This SF.net email is sponsored by 

Make an app they can't live without
Enter the BlackBerry Developer Challenge
http://p.sf.net/sfu/RIM-dev2dev 
_______________________________________________
Bacula-users mailing list
Bacula-users AT lists.sourceforge DOT net
https://lists.sourceforge.net/lists/listinfo/bacula-users

  

Attachment: jrlang.vcf
Description: Vcard

------------------------------------------------------------------------------
This SF.net email is sponsored by 

Make an app they can't live without
Enter the BlackBerry Developer Challenge
http://p.sf.net/sfu/RIM-dev2dev 
_______________________________________________
Bacula-users mailing list
Bacula-users AT lists.sourceforge DOT net
https://lists.sourceforge.net/lists/listinfo/bacula-users