On Wednesday 08 September 2004 14:31, Stefan G. Weichinger wrote:
>Hi, Gene,
>
>on Mittwoch, 08. September 2004 at 19:27 you wrote to amanda-users:
>>>The loop to create the vtapes runs from 1 to 12, the loop to label
>>>starts with 01, 02, ...
>
>GH> I made them by hand, and chown-ed everything after.
>
>I fixed the HOWTO anyway.
>
>GH> Let me save the fixed amanda.conf and see what happens, but I
> think GH> the installed libs are hardcoded to use /dev/nst0 thanks
> to my gh.cf GH> that I've published since forever here on this
> list. How should I GH> modify that? Its presently:
>
>ONCE AGAIN !!!! ;-) :
>
>I think I have to add this to the tarball to stop you from doing
> this ;-)
>
>GH> ./configure --with-user=amanda \
>GH> --with-group=disk \
>GH> --with-owner=amanda \
>GH> --with-gnu-ld --prefix=/usr/local \
>GH> --with-tapedev=FILE:/amandatapes
>....
>
>GH> Is this anywhere near usable?
>
>I don't know. I assume it is ok. Maybe use
>
>--with-tapedev="FILE:/amandatapes"
>
>Could you try this and tell us? Thanks.
That would be the only line in that config driver thats dbl quoted, but I tried
it, nuked everything and re-built and installed it, no real diffs to be seen.
I've rebuilt it several times with this config:
--------------
#!/bin/sh
# since I'm always forgetting to su amanda...
if [ `whoami` != 'amanda' ]; then
echo
echo "!!!!!!!!!!!! Warning !!!!!!!!!!!!"
echo "Amanda needs to be configured and built by the user amanda,"
echo "but must be installed by user root."
echo
exit 1
fi
make clean
rm -f config.status config.cache
./configure --with-user=amanda \
--with-group=disk \
--with-owner=amanda \
--with-gnu-ld \
--prefix=/usr/local \
--with-tapedev="FILE:/amandatapes" \
--with-debugging=/tmp/amanda-dbg/ \
--with-tape-server=coyote.coyote.den \
--with-amandahosts \
--with-configdir=/usr/local/etc/amanda
make
--------------
This is run as user amanda, and root then installs the build.
Here is the whole amanda.conf, in case I've got a name clash someplace.
--------------
#
# amanda.conf - sample Amanda configuration file. This started off life as
# the actual config file in use at CS.UMD.EDU.
#
# If your configuration is called, say, "csd", then this file normally goes
# in /usr/local/etc/amanda/csd/amanda.conf.
#
org "DailySet1" # your organization name for reports
mailto "root AT coyote.coyote DOT den" # space separated list of operators at
your site
dumpuser "amanda" # the user to run dumps under
inparallel 3 # maximum dumpers that will run in parallel (max 63)
# this maximum can be increased at compile-time,
# modifying MAX_DUMPERS in server-src/driverio.h
maxdumps 3 # allowing one per disk make sense to me
taperalgo largestfit # will help fill tapes if runtapes >1!
netusage 800 Kbps # maximum net bandwidth for Amanda, in KB per sec
dumpcycle 8 days # the number of days in the normal dump cycle
runspercycle 8 # the number of amdump runs in dumpcycle days
# (4 weeks * 5 amdump runs per week -- just weekdays)
tapecycle 28 tapes # the number of tapes in rotation
# 4 weeks (dumpcycle) times 5 tapes per week (just
# the weekdays) plus a few to handle errors that
# need amflush and so we do not overwrite the full
# backups performed at the beginning of the previous
# cycle
autoflush yes
dumporder "STTT" # specify the priority order of each dumper
# s -> smallest size
# S -> biggest size
# t -> smallest time
# T -> biggest time
# b -> smallest bandwidth
# B -> biggest bandwidth
# try "BTBTBTBTBTBT" if you are not holding
# disk constrained
# BUT, if you want streaming, start with the
# big ones and work down
### ### ###
# WARNING: don't use `inf' for tapecycle, it's broken!
### ### ###
bumpsize 20 Mb # minimum savings (threshold) to bump level 1 -> 2
bumpdays 2 # minimum days at each level
bumpmult 2 # threshold = bumpsize * bumpmult^(level-1)
etimeout 900 # number of seconds per filesystem for estimates.
#etimeout -600 # total number of seconds for estimates.
# a positive number will be multiplied by the number of filesystems on
# each host; a negative number will be taken as an absolute total time-out.
# The default is 5 minutes per filesystem.
dtimeout 1800 # number of idle seconds before a dump is aborted.
ctimeout 4 # maximum number of seconds that amcheck waits
# for each client host
tapebufs 120
# A positive integer telling taper how many 32k buffers to allocate.
# WARNING! If this is set too high, taper will not be able to allocate
# the memory and will die. The default is 20 (640k).
# I wonder what the limit might be, its been running at 60 for months
# so try 80. Still works fine, I have a gig of ram.
# Specify tape device and/or tape changer. If you don't have a tape
# changer, and you don't want to use more than one tape per run of
# amdump, just comment out the definition of tpchanger.
# Some tape changers require tapedev to be defined; others will use
# their own tape device selection mechanism. Some use a separate tape
# changer device (changerdev), others will simply ignore this
# parameter. Some rely on a configuration file (changerfile) to
# obtain more information about tape devices, number of slots, etc;
# others just need to store some data in files, whose names will start
# with changerfile. For more information about individual tape
# changers, read docs/TAPE.CHANGERS.
# At most one changerfile entry must be defined; select the most
# appropriate one for your configuration. If you select man-changer,
# keep the first one; if you decide not to use a tape changer, you may
# comment them all out.
runtapes 10 # number of tapes to be used in a single run of amdump
#tpchanger "chg-scsi" # the tape-changer glue script
#tpchanger "chg-mtx"
tpchanger "changer"
#tapedev "0" # the no-rewind tape device to be used
tapedev "FILE:/amandatapes/DailySet1"
rawtapedev "FILE:/amandatapes/Dailyset1"
#changerfile "/usr/local/etc/amanda/DailySet1/chg-scsi.conf"
#changerfile "/usr/local/etc/amanda/DailySet1/chg.mtx.conf"
changerfile "/usr/local/etc/amanda/DailySet1/changer"
#tapetype DDS2 # what kind of tape it is (see tapetypes below)
tapetype HARD-DISK
labelstr "^DailySet1-[0-9][0-9]*$" # label constraint regex: all tapes must
match
amrecover_do_fsf yes # amrecover will call amrestore with the
# -f flag for faster positioning of the tape.
amrecover_check_label yes # amrecover will call amrestore with the
# -l flag to check the label.
#amrecover_changer "chg-scsi" # amrecover will use the changer if you restore
#amrecover_changer "chg-mtx" # from this device.
amrecover_changer "changer"
# Specify holding disks. These are used as a temporary staging area for
# dumps before they are written to tape and are recommended for most sites.
# The advantages include: tape drive is more likely to operate in streaming
# mode (which reduces tape and drive wear, reduces total dump time); multiple
# dumps can be done in parallel (which can dramatically reduce total dump time.
# The main disadvantage is that dumps on the holding disk need to be flushed
# (with amflush) to tape after an operating system crash or a tape failure.
# If no holding disks are specified then all dumps will be written directly
# to tape. If a dump is too big to fit on the holding disk than it will be
# written directly to tape. If more than one holding disk is specified then
# they will all be used based on activity and available space.
holdingdisk hd1 {
comment "main holding disk"
directory "/dumps" # where the holding disk is
use -500 Mb # how much space can we use on it
# a non-positive value means:
# use all space but that value
chunksize 1Gb # size of chunk if you want big dump to be
# dumped on multiple files on holding disks
# N Kb/Mb/Gb split images in chunks of size N
# The maximum value should be
# (MAX_FILE_SIZE - 1Mb)
# 0 same as INT_MAX bytes
}
#holdingdisk hd2 {
# directory "/dumps2/amanda"
# use 1000 Mb
# }
#holdingdisk hd3 {
# directory "/mnt/disk4"
# use 1000 Mb
# }
# If amanda cannot find a tape on which to store backups, it will run
# as many backups as it can to the holding disks. In order to save
# space for unattended backups, by default, amanda will only perform
# incremental backups in this case, i.e., it will reserve 100% of the
# holding disk space for the so-called degraded mode backups.
# However, if you specify a different value for the `reserve'
# parameter, amanda will not degrade backups if they will fit in the
# non-reserved portion of the holding disk.
reserve 30 # percent
# This means save at least 30% of the holding disk space for degraded
# mode backups.
# The format for a ColumnSpec is a ',' seperated list of triples.
# Each triple consists of
# + the name of the column (as in ColumnNameStrings)
# + prefix before the column
# + the width of the column, if set to -1 it will be recalculated
# to the maximum length of a line to print.
# Example:
# "Disk=1:17,HostName=1:10,OutKB=1:7"
# or
# "Disk=1:-1,HostName=1:10,OutKB=1:7"
#
# You need only specify those colums that should be changed from
# the default. If nothing is specified in the configfile, the
# above compiled in values will be in effect, resulting in an
# output as it was all the time.
# The names of the colums are:
# HostName, Disk, Level, OrigKB, OutKB, Compress, DumpTime, DumpRate,
# TapeTime and TapeRate.
# ElB, 1999-02-24.
columnspec
"Disk=1:18,HostName=0:10,Level=1:3,OrigKB=1:9,OutKB=1:9,Compress=1:7,DumpTime=1:7,DumpRate=1:7,TapeTime=1:7,TapeRate=1:7"
# Amanda needs a few Mb of diskspace for the log and debug files,
# as well as a database. This stuff can grow large, so the conf directory
# isn't usually appropriate. Some sites use /usr/local/var and some /usr/adm.
# Create an amanda directory under there. You need a separate infofile and
# logdir for each configuration, so create subdirectories for each conf and
# put the files there. Specify the locations below.
# Note that, although the keyword below is infofile, it is only so for
# historic reasons, since now it is supposed to be a directory (unless
# you have selected some database format other than the `text' default)
infofile "/usr/local/var/amanda/DailySet1/curinfo" # database DIRECTORY
logdir "/usr/local/var/amanda/DailySet1" # log directory
indexdir "/usr/local/var/amanda/DailySet1/index" # index directory
tapelist "/usr/local/etc/amanda/DailySet1/tapelist" # list of used tapes
# tapelist is stored, by default, in the directory that contains amanda.conf
# tapetypes
# Define the type of tape you use here, and use it in "tapetype"
# above. Some typical types of tapes are included here. The tapetype
# tells amanda how many MB will fit on the tape, how big the filemarks
# are, and how fast the tape device is.
# A filemark is the amount of wasted space every time a tape section
# ends. If you run `make tapetype' in tape-src, you'll get a program
# that generates tapetype entries, but it is slow as hell, use it only
# if you really must and, if you do, make sure you post the data to
# the amanda mailing list, so that others can use what you found out
# by searching the archives.
# For completeness Amanda should calculate the inter-record gaps too,
# but it doesn't. For EXABYTE and DAT tapes this is ok. Anyone using
# 9 tracks for amanda and need IRG calculations? Drop me a note if
# so.
# If you want amanda to print postscript paper tape labels
# add a line after the comment in the tapetype of the form
# lbl-templ "/path/to/postscript/template/label.ps"
# if you want the label to go to a printer other than the default
# for your system, you can also add a line above for a different
# printer. (i usually add that line after the dumpuser specification)
# dumpuser "operator" # the user to run dumps under
# printer "mypostscript" # printer to print paper label on
# here is an example of my definition for an EXB-8500
# define tapetype EXB-8500 {
# ...
# lbl-templ "/usr/local/amanda/config/lbl.exabyte.ps"
# }
define tapetype HARD-DISK {
comment "Dump onto hard disk"
length 6000 mbytes # specified in mbytes to get the exact
size of 6GB
}
define tapetype QIC-60 {
comment "Archive Viper"
length 60 mbytes
filemark 100 kbytes # don't know a better value
speed 100 kbytes # dito
}
define tapetype DEC-DLT2000 {
comment "DEC Differential Digital Linear Tape 2000"
length 15000 mbytes
filemark 8 kbytes
speed 1250 kbytes
}
# goluboff AT butch.Colorado DOT EDU
# in amanda-users (Thu Dec 26 01:55:38 MEZ 1996)
define tapetype DLT {
comment "DLT tape drives"
length 20000 mbytes # 20 Gig tapes
filemark 2000 kbytes # I don't know what this means
speed 1536 kbytes # 1.5 Mb/s
}
define tapetype SURESTORE-1200E {
comment "HP AutoLoader"
length 3900 mbytes
filemark 100 kbytes
speed 500 kbytes
}
define tapetype EXB-8500 {
comment "Exabyte EXB-8500 drive on decent machine"
length 4200 mbytes
filemark 48 kbytes
speed 474 kbytes
}
define tapetype EXB-8200 {
comment "Exabyte EXB-8200 drive on decent machine"
length 2200 mbytes
filemark 2130 kbytes
speed 240 kbytes
}
define tapetype HP-DAT {
comment "DAT tape drives"
# data provided by Rob Browning <rlb AT cs.utexas DOT edu>
length 1930 mbytes
filemark 111 kbytes
speed 468 kbytes
}
define tapetype DDS2 {
comment "DDS2 drives with 120 meter tapes"
length 3600 mbytes
speed 397 kps
filemark 0 kbytes
blocksize 32k
}
define tapetype DAT {
comment "DAT tape drives"
length 1000 mbytes # these numbers are not accurate
filemark 100 kbytes # but you get the idea
speed 100 kbytes
}
define tapetype MIMSY-MEGATAPE {
comment "Megatape (Exabyte based) drive through Emulex on Vax 8600"
length 2200 mbytes
filemark 2130 kbytes
speed 170 kbytes # limited by the Emulex bus interface, ugh
}
# dumptypes
#
# These are referred to by the disklist file. The dumptype specifies
# certain parameters for dumping including:
# auth - authentication scheme to use between server and client.
# Valid values are "bsd" and "krb4". Default: [auth bsd]
# comment - just a comment string
# comprate - set default compression rate. Should be followed by one or
# two numbers, optionally separated by a comma. The 1st is
# the full compression rate; the 2nd is the incremental rate.
# If the second is omitted, it is assumed equal to the first.
# The numbers represent the amount of the original file the
# compressed file is expected to take up.
# Default: [comprate 0.50, 0.50]
# compress - specify compression of the backed up data. Valid values are:
# "none" - don't compress the dump output.
# "client best" - compress on the client using the best (and
# probably slowest) algorithm.
# "client fast" - compress on the client using fast algorithm.
# "server best" - compress on the tape host using the best (and
# probably slowest) algorithm.
# "server fast" - compress on the tape host using a fast
# algorithm. This may be useful when a fast
# tape host is backing up slow clients.
# Default: [compress client fast]
# dumpcycle - set the number of days in the dump cycle, ie, set how often a
# full dump should be performed. Default: from DUMPCYCLE above
# exclude - specify files and directories to be excluded from the dump.
# Useful with gnutar only; silently ignored by dump and samba.
# Valid values are:
# "pattern" - a shell glob pattern defining which files
# to exclude.
# gnutar gets --exclude="pattern"
# list "filename" - a file (on the client!) containing patterns
# re's (1 per line) defining which files to
# exclude.
# gnutar gets --exclude-from="filename"
# Note that the `full pathname' of a file within its
# filesystem starts with `./', because of the way amanda runs
# gnutar: `tar -C $mountpoint -cf - --lots-of-options .' (note
# the final dot!) Thus, if you're backing up `/usr' with a
# diskfile entry like ``host /usr gnutar-root', but you don't
# want to backup /usr/tmp, your exclude list should contain
# the pattern `./tmp', as this is relative to the `/usr' above.
# Please refer to the man-page of gnutar for more information.
# If a relative pathname is specified as the exclude list,
# it is searched from within the directory that is
# going to be backed up.
# Default: include all files
# holdingdisk - should the holding disk be used for this dump. Useful for
# dumping the holding disk itself. Default: [holdingdisk yes]
# ignore - do not back this filesystem up. Useful for sharing a single
# disklist in several configurations.
# index - keep an index of the files backed up. Default: [index no]
# kencrypt - encrypt the data stream between the client and server.
# Default: [kencrypt no]
# maxdumps - max number of concurrent dumps to run on the client.
# Default: [maxdumps 1]
# priority - priority level of the dump. Valid levels are "low", "medium"
# or "high". These are really only used when Amanda has no
# tape to write to because of some error. In that "degraded
# mode", as many incrementals as will fit on the holding disk
# are done, higher priority first, to insure the important
# disks are at least dumped. Default: [priority medium]
# program - specify the dump system to use. Valid values are "DUMP" and
# "GNUTAR". Default: [program "DUMP"].
# record - record the dump in /etc/dumpdates. Default: [record yes]
# skip-full - skip the disk when a level 0 is due, to allow full backups
# outside Amanda, eg when the machine is in single-user mode.
# skip-incr - skip the disk when the level 0 is NOT due. This is used in
# archive configurations, where only full dumps are done and
# the tapes saved.
# starttime - delay the start of the dump? Default: no delay
# strategy - set the dump strategy. Valid strategies are currently:
# "standard" - the standard one.
# "nofull" - do level 1 dumps every time. This can be used,
# for example, for small root filesystems that
# only change slightly relative to a site-wide
# prototype. Amanda then backs up just the
# changes.
# "noinc" - do level 0 dumps every time.
# Unfortunately, this is not currently
# implemented. Use `dumpcycle 0'
# instead.
# "skip" - skip all dumps. Useful for sharing a single
# disklist in several configurations.
# "incronly" - do only incremental dumps. This is similar
# to strategy 'nofull', but will increase
# the dump level as usual. Full dumps will
# only be performed when an 'amadmin force'
# has been issued
# Default: [strategy standard]
#
# Note that you may specify previously defined dumptypes as a shorthand way
# of defining parameters.
define dumptype global {
comment "Global definitions"
# This is quite useful for setting global parameters, so you don't have
# to type them everywhere. All dumptype definitions in this sample file
# do include these definitions, either directly or indirectly.
# There's nothing special about the name `global'; if you create any
# dumptype that does not contain the word `global' or the name of any
# other dumptype that contains it, these definitions won't apply.
# Note that these definitions may be overridden in other
# dumptypes, if the redefinitions appear *after* the `global'
# dumptype name.
# You may want to use this for globally enabling or disabling
# indexing, recording, etc. Some examples:
index yes
# record no
}
define dumptype always-full {
global
comment "Full dump of this filesystem always"
compress none
priority high
dumpcycle 0
}
define dumptype root-tar {
global
program "GNUTAR"
comment "root partitions dumped with tar"
compress none
# exclude the work dir for my scripts, but get the scripts
# exclude list "/amanda/.config-bak"
priority low
}
define dumptype coyote-tar {
root-tar
exclude list "/amanda/.config-bak"
}
define dumptype gene-tar {
root-tar
}
define dumptype user-tar {
root-tar
comment "user partitions dumped with tar"
priority medium
}
define dumptype high-tar {
root-tar
comment "partitions dumped with tar"
priority high
}
define dumptype comp-root-tar {
root-tar
comment "Root partitions with compression"
compress client best
comprate 0.40, 0.44
}
define dumptype comp-coyote-tar {
comp-root-tar
exclude list "/amanda/.config-bak"
}
define dumptype comp-gene-tar {
comp-root-tar
}
define dumptype comp-user-tar {
user-tar
compress client fast
}
define dumptype holding-disk {
global
comment "The master-host holding disk itself"
holdingdisk no # do not use the holding disk
priority medium
}
define dumptype comp-user {
global
comment "Non-root partitions on reasonably fast machines"
compress client fast
priority medium
}
define dumptype nocomp-user {
comp-user
comment "Non-root partitions on slow machines"
compress none
}
define dumptype comp-root {
global
comment "Root partitions with compression"
compress client fast
priority low
}
define dumptype nocomp-root {
comp-root
comment "Root partitions without compression"
compress none
}
define dumptype comp-high {
global
comment "very important partitions on fast machines"
compress client best
priority high
}
define dumptype nocomp-high {
comp-high
comment "very important partitions on slow machines"
compress none
}
define dumptype nocomp-test {
global
comment "test dump without compression, no /etc/dumpdates recording"
compress none
record no
priority medium
}
define dumptype comp-test {
nocomp-test
comment "test dump with compression, no /etc/dumpdates recording"
compress client best
}
# network interfaces
#
# These are referred to by the disklist file. They define the attributes
# of the network interface that the remote machine is accessed through.
# Notes: - netusage above defines the attributes that are used when the
# disklist entry doesn't specify otherwise.
# - the values below are only samples.
# - specifying an interface does not force the traffic to pass
# through that interface. Your OS routing tables do that. This
# is just a mechanism to stop Amanda trashing your network.
# Attributes are:
# use - bandwidth above which amanda won't start
# backups using this interface. Note that if
# a single backup will take more than that,
# amanda won't try to make it run slower!
define interface local {
comment "a local disk"
use 1000 kbps
}
define interface le0 {
comment "100 Mbps ethernet"
use 5000 kbps
}
# You may include other amanda configuration files, so you can share
# dumptypes, tapetypes and interface definitions among several
# configurations.
#includefile "/usr/local/amanda.conf.main"
---------------
And I now note that in my attempts to run amcheck or amlabel,
I now have files in the /config/ dir named -access, -clean
and -slot, which tells me the name string those are supposed
to be appended to is a null string, probaby because the name
'changer' isn't correct, or is not correctly keyword identified.
As current built and installed with the above ./gh.cf,
running this script as ./mkamandatapes
----------------
#!/bin/sh
for n in 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27
do
amlabel DailySet1 DailySet1-${n} slot ${n}
done
----------------
returns this when run:
[amanda@coyote DailySet1]$ ./mkamandatapes
amlabel: could not load slot "00": could not read result from
"/usr/local/libexec/changer"
amlabel: could not load slot "01": could not read result from
"/usr/local/libexec/changer"
...etc
and a run of amcheck gets this:
---------------
[amanda@coyote amanda-2.4.5b1-20040831]$ amcheck DailySet1
amcheck: error while loading shared libraries: libamserver-2.4.5b1-20040831.so:
cannot open shared object file: Nosuch file or directory
----------------
The library does indeed exist:
[amanda@coyote amanda-2.4.5b1-20040831]$ ls -l /usr/local/lib/libam*
-rwxr-xr-x 1 root root 505543 Sep 8 19:38
/usr/local/lib/libamanda-2.4.5b1-20040831.so
-rw-r--r-- 1 root root 1017448 Sep 8 19:38 /usr/local/lib/libamanda.a
-rwxr-xr-x 1 root root 865 Sep 8 19:38 /usr/local/lib/libamanda.la
lrwxr-xr-x 1 root root 29 Sep 8 19:38 /usr/local/lib/libamanda.so ->
libamanda-2.4.5b1-20040831.so
-rwxr-xr-x 1 root root 133417 Sep 8 19:38
/usr/local/lib/libamclient-2.4.5b1-20040831.so
-rw-r--r-- 1 root root 244814 Sep 8 19:38 /usr/local/lib/libamclient.a
-rwxr-xr-x 1 root root 879 Sep 8 19:38 /usr/local/lib/libamclient.la
lrwxr-xr-x 1 root root 31 Sep 8 19:38 /usr/local/lib/libamclient.so ->
libamclient-2.4.5b1-20040831.so
-rwxr-xr-x 1 root root 397648 Sep 8 19:38
/usr/local/lib/libamserver-2.4.5b1-20040831.so
-rw-r--r-- 1 root root 735114 Sep 8 19:38 /usr/local/lib/libamserver.a
-rwxr-xr-x 1 root root 879 Sep 8 19:38 /usr/local/lib/libamserver.la
lrwxr-xr-x 1 root root 31 Sep 8 19:38 /usr/local/lib/libamserver.so ->
libamserver-2.4.5b1-20040831.so
-rwxr-xr-x 1 root root 161656 Sep 8 19:38
/usr/local/lib/libamtape-2.4.5b1-20040831.so
-rw-r--r-- 1 root root 280428 Sep 8 19:38 /usr/local/lib/libamtape.a
-rwxr-xr-x 1 root root 865 Sep 8 19:38 /usr/local/lib/libamtape.la
lrwxr-xr-x 1 root root 29 Sep 8 19:38 /usr/local/lib/libamtape.so ->
libamtape-2.4.5b1-20040831.so
--------------
>Apart from that, AFAIK the configure-options are just defaults, and
>your amanda.conf-settings override them so you are able to use
>chg-disk in your conf without recompiling.
>
>While I type this, I realize that I even use it that way myself.
>
>;-)
It should work so easy here. I'm gonna go read some src I guess.
If anyone else can see where the error(s) might be, yelp, I check
the mail every ten minutes. That doesn't mean I see it that fast
as I've also been in the woodshop resawing a couple of cherry planks
to make door panels for an entertainment center. And my 12"
Craftsman bandsaw really isn't up frame or motorwise, to a brand
new, pretty agressive TimberWolf saw blade. But thats what I brung
to this party, so it will have to do. Nice curley cherry, those
2 planks, will make "purty" door inserts. :-)
--
Cheers, Gene
"There are four boxes to be used in defense of liberty:
soap, ballot, jury, and ammo. Please use in that order."
-Ed Howdershelt (Author)
99.25% setiathome rank, not too shabby for a WV hillbilly
Yahoo.com attorneys please note, additions to this message
by Gene Heskett are:
Copyright 2004 by Maurice Eugene Heskett, all rights reserved.
|
