We have purchased a jukebox with imbedded LTO2 tape drive.
The system we have attached it to is running kernel 2.4.20-24 on
Red Hat Linux release 9 (Shrike).
While we seem to see the tape drive during the system boot I'm
either not addressing it correctly or its not fully configured.
DMESG output follows.
And the attempts to access the device via mt fail:
# mt -f /dev/st0 status
/dev/st0: No such device or address
Do we need to update a driver, run a config command or are we just
using the wrong name for the tape device ?
Off hand, how do I find the name for the robot ?
thank you,
Brian
---
Brian R Cuttler brian.cuttler AT wadsworth DOT org
Computer Systems Support (v) 518 486-1697
Wadsworth Center (f) 518 473-6384
NYS Department of Health Help Desk 518 473-0773
Linux version 2.4.20-24.9 (bhcompile AT porky.devel.redhat DOT com) (gcc
version 3.2.2 20030222 (Red Hat Linux 3.2.2-5)) #1 Mon Dec 1 11:35:51 EST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ff77000 (usable)
BIOS-e820: 000000001ff77000 - 000000001ff79000 (ACPI NVS)
BIOS-e820: 000000001ff79000 - 0000000020000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
On node 0 totalpages: 130935
zone(0): 4096 pages.
zone(1): 126839 pages.
zone(2): 0 pages.
Kernel command line: ro root=LABEL=/ hdc=ide-scsi
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 1794.566 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3578.26 BogoMIPS
Memory: 510860k/523740k available (1358k kernel code, 10320k reserved, 1004k
data, 132k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 3febfbff 00000000 00000000 00000000
CPU: Common caps: 3febfbff 00000000 00000000 00000000
CPU: Intel(R) Pentium(R) 4 CPU 1.80GHz stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch AT atnf.csiro DOT au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfbe8e, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Bridge
PCI: Using IRQ router PIIX [8086/2440] at 00:1f.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ
SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
ttyS1 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta3-.2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH2: IDE controller at PCI slot 00:1f.1
ICH2: chipset revision 4
ICH2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: MAXTOR 6L040L2, ATA DISK drive
hdb: WDC WD1600JB-00GVA0, ATA DISK drive
blk: queue c03cdfe0, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c03ce124, I/O limit 4095Mb (mask 0xffffffff)
hdc: HL-DT-ST GCE-8160B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 78177792 sectors (40027 MB) w/1819KiB Cache, CHS=4866/255/63, UDMA(33)
hdb: attached ide-disk driver.
hdb: host protected area => 1
hdb: 312581808 sectors (160042 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(33)
ide-floppy driver 0.99.newide
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
hdb: hdb1
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 145k freed
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 132k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 11:43:19 Dec 1 2003
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 11 for device 00:1f.2
PCI: Setting latency timer of device 00:1f.2 to 64
usb-uhci.c: USB UHCI at I/O 0xff80, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 9 for device 00:1f.4
PCI: Setting latency timer of device 00:1f.4 to 64
usb-uhci.c: USB UHCI at I/O 0xff60, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech AT suse DOT cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
Adding Swap: 1052216k swap-space (priority -1)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,65), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SCSI subsystem driver Revision: 1.00
hdc: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: HL-DT-ST Model: CD-RW GCE-8160B Rev: 2.11
Type: CD-ROM ANSI SCSI revision: 02
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
PCI: Found IRQ 11 for device 02:09.0
PCI: Sharing IRQ 11 with 02:0c.0
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.8
<Adaptec 29160 Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
blk: queue dfab4a14, I/O limit 4095Mb (mask 0xffffffff)
Vendor: M4 DATA Model: MagFile Rev: 6.0
Type: Medium Changer ANSI SCSI revision: 02
blk: queue dfab4c14, I/O limit 4095Mb (mask 0xffffffff)
Vendor: HP Model: Ultrium 2-SCSI Rev: F45Z
Type: Sequential-Access ANSI SCSI revision: 03
blk: queue dee3f014, I/O limit 4095Mb (mask 0xffffffff)
scsi : 1 host left.
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
ip_conntrack version 2.1 (4091 buckets, 32728 max) - 292 bytes per conntrack
PCI: Found IRQ 11 for device 02:0c.0
PCI: Sharing IRQ 11 with 02:09.0
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
See Documentation/networking/vortex.txt
02:0c.0: 3Com PCI 3c905C Tornado at 0xe880. Vers LK1.1.18-ac
00:06:5b:dd:02:54, IRQ 11
product code 0e85 rev 00.6 date 02-18-02
Internal config register is 1800000, transceivers 0xa.
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 782d.
Enabling bus-master transmits and whole-frame receives.
02:0c.0: scatter/gather enabled. h/w checksums enabled
divert: allocating divert_blk for eth0
iSCSI: 3.1.0.3 ( 8-Oct-2002) built for Linux 2.4.20-24.9
iSCSI: will translate deferred sense to current sense on command responses
iSCSI: control device major number 254
iSCSI: detected HBA c23e69f8, host #2
scsi2 : iSCSI 3.1.0.3 ( 8-Oct-2002)
0: nvidia: loading NVIDIA Linux x86 nvidia.o Kernel Module 1.0-4496 Wed Jul
16 19:03:09 PDT 2003
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Intel i850 chipset
agpgart: AGP aperture is 128M @ 0xe8000000
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
PCI: Enabling device 02:09.0 (0116 -> 0117)
PCI: Found IRQ 11 for device 02:09.0
PCI: Sharing IRQ 11 with 02:0c.0
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.8
<Adaptec 29160 Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
blk: queue db93ae14, I/O limit 4095Mb (mask 0xffffffff)
Vendor: M4 DATA Model: MagFile Rev: 6.0
Type: Medium Changer ANSI SCSI revision: 02
blk: queue db93aa14, I/O limit 4095Mb (mask 0xffffffff)
Vendor: HP Model: Ultrium 2-SCSI Rev: F45Z
Type: Sequential-Access ANSI SCSI revision: 03
blk: queue d4fa7014, I/O limit 4095Mb (mask 0xffffffff)
st: Version 20030406, bufsize 32768, max init. bufs 4, s/g segs 16
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 8
Attached scsi tape st0 at scsi1, channel 0, id 1, lun 0
scsi : 2 hosts left.
Creative EMU10K1 PCI Audio Driver, version 0.20, 11:44:07 Dec 1 2003
----- End forwarded message -----
---
Brian R Cuttler brian.cuttler AT wadsworth DOT org
Computer Systems Support (v) 518 486-1697
Wadsworth Center (f) 518 473-6384
NYS Department of Health Help Desk 518 473-0773
|
