Hello,
But where can I get the dot1dBridge MIB?? Any idea or any pointers to
the same??
Also any special procedures we have to do after we load the MIB??
Also I have another problem, when I open the Netview web console, and if
the default map is open on the Netview server then all goes fine
properly. But if I have saved any map to a new map and open the same in
the server, and then I open the web console it doesn't at all open the
map, what I mean is the login to console happens but after that when I
say file and open map in web console, it says error: no maps currently
open. But the same when I open the default map in the server it doesn't
give me this error.
What can be the reasons??
Regards,
Mithun Prabhu
System Engineer, ITO
Infosys Technologies Limited
Direct:080-4175689
Fax : 852 0362
Home: www.infosys.com
-----Original Message-----
From: Jeffrey G. Fitzwater [mailto:jfitz AT Princeton DOT EDU]
Sent: Tuesday, January 07, 2003 7:47 PM
To: Jane Curry
Cc: Mithun Prakash Prabhu; nv-l AT lists.tivoli DOT com
Subject: Re: [nv-l] NV 713 and MIBs to find inactive ports in Cisco
Switches.
Jane Curry wrote:
> Mithun,
> The application you have on the Web Console only requires the switch
to
> support the dot1dBridge MIB (RFC 1493).
> Cheers,
> Jane
>
> Mithun Prakash Prabhu wrote:
>
> > Hi list,
> >
> > I have installed Netview ver 7.1.3, I have discovered some Cisco
4006
> > switches via the server discovery. Now I wanted to know what MIB you
> > need to load in order to find out the INACTIVE ports in a cisco
> > switch. Ie those ports where its either not been used or been
disabled.
> >
> > Also when I open the NV Web console using a login id and password I
> > see there a view inactive ports in a network device option, which
> > gives me no values. I have some cisco MIBs downloaded but don?t know
> > which one?s will help me. Please can any one let me know the same.
> >
> > Thanks in Advance.
> >
> > /*/Regards,/*/
> >
> > /*/Mithun Prabhu /*/*/
> > /*
> >
>
>-----------------------------------------------------------------------
-
> >
> >---------------------------------------------------------------------
> >To unsubscribe, e-mail: nv-l-unsubscribe AT lists.tivoli DOT com
> >For additional commands, e-mail: nv-l-help AT lists.tivoli DOT com
> >
> >*NOTE*
> >This is not an Offical Tivoli Support forum. If you need immediate
> >assistance from Tivoli please call the IBM Tivoli Software Group
> >help line at 1-800-TIVOLI8(848-6548)
> >
>
> --
> Tivoli Certified Consultant & Instructor
> Skills 1st Limited, 2 Cedar Chase, Taplow, Bucks, SL6 0EU, UK
> Tel: +44 (0)1628 782565
> Copyright (c) 2003 Jane Curry <jane.curry AT skills-1st.co DOT uk>. All
rights reserved.
>
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: nv-l-unsubscribe AT lists.tivoli DOT com
> For additional commands, e-mail: nv-l-help AT lists.tivoli DOT com
>
> *NOTE*
> This is not an Offical Tivoli Support forum. If you need immediate
> assistance from Tivoli please call the IBM Tivoli Software Group
> help line at 1-800-TIVOLI8(848-6548)
I might note that dot1dBridge MIB (RFC 1493) supports COMMUNITY STRING
INDEXING, so
if you are not using vlan 1 you must append @vlanNumber after the
community name in
order to get the mib info from other vlans, otherwise only vlan 1 data
will be
retrieved. Also if you do append the @vlanNumber and you only have
vlan 1 then it
will retrieve vlan1 info. IE.. public@122
Jeff Fitzwater
OIT Systems & Networking
Princeton University
|
