Zitat von Marco van Wieringen <mvw AT planets.elm DOT net>:

> Its something set in the changer.
>
> Check the tandberg web interface (guess the small 1u also has one)
> my 24 slots has one at least.
>
> Go to the Configure/Cleaning menu and make sure Fixed Cleaning Slot Enabled:
> is disabled and auto clean on is grayed out.
>
> You can also look at the front menu and do
>
> Maint
> Cleaning Options
> Fixed Cleaning Slot
>
> Should show something like Fixed Cleaning Slot x: Disabled.
>
> Marco

When I log in into the web interface I see 8 usable slots. This is  
where I told the changer that my former cleaning slot number 8 is no  
longer a cleaning slot. On the Status-page I see the two magazines  
with 4 tapes each. There is no cleaning slot defined, i.e. I set the  
cleaning slot to 0 which is what the manual suggests.

I did a firmware upgrade hoping that this will fix my problem. I  
encountered something strange as the following command (/dev/sg4 is  
the changer) gives two different outputs:

boromir ~/tdtool # mtx -f /dev/sg4 status
RequestSense (0x03) failed
mtx: Request Sense: Long Report=yes
mtx: Request Sense: Valid Residual=no
mtx: Request Sense: Error Code=70 (Current)
mtx: Request Sense: Sense Key=Unit Attention
mtx: Request Sense: FileMark=no
mtx: Request Sense: EOM=no
mtx: Request Sense: ILI=no
mtx: Request Sense: Additional Sense Code = 28
mtx: Request Sense: Additional Sense Qualifier = 00
mtx: Request Sense: BPV=no
mtx: Request Sense: Error in CDB=no
mtx: Request Sense: SKSV=no
Mode sense (0x1A) for Page 0x1D failed
   Storage Changer /dev/sg4:1 Drives, 8 Slots ( 0 Import/Export )
Data Transfer Element 0:Full (Storage Element 3 Loaded):VolumeTag = WOC4-03L4
       Storage Element 1:Full :VolumeTag=WOC4-01L4
       Storage Element 2:Full :VolumeTag=WOC4-02L4
       Storage Element 3:Empty
       Storage Element 4:Full :VolumeTag=WOC5-01L4
       Storage Element 5:Full :VolumeTag=WOC5-02L4
       Storage Element 6:Full :VolumeTag=WOC5-03L4
       Storage Element 7:Full :VolumeTag=WOC1-01L4
       Storage Element 8:Full :VolumeTag=WOC1-02L4

boromir ~/tdtool # mtx -f /dev/sg4 status
   Storage Changer /dev/sg4:1 Drives, 7 Slots ( 0 Import/Export )
Data Transfer Element 0:Full (Storage Element 3 Loaded):VolumeTag = WOC4-03L4
       Storage Element 1:Full :VolumeTag=WOC4-01L4
       Storage Element 2:Full :VolumeTag=WOC4-02L4
       Storage Element 3:Empty
       Storage Element 4:Full :VolumeTag=WOC5-01L4
       Storage Element 5:Full :VolumeTag=WOC5-02L4
       Storage Element 6:Full :VolumeTag=WOC5-03L4
       Storage Element 7:Full :VolumeTag=WOC1-01L4

The two commands were issued directly one after another because I  
worried about the first responses of the changer (RequestSense (0x03)  
failed ...).

Greetings
--
Jens


------------------------------------------------------------------------------
Live Security Virtual Conference
Exclusive live event will cover all the ways today's security and 
threat landscape has changed and how IT managers can respond. Discussions 
will include endpoint security, mobile security and the latest in malware 
threats. http://www.accelacomm.com/jaw/sfrnl04242012/114/50122263/
_______________________________________________
Bacula-users mailing list
Bacula-users AT lists.sourceforge DOT net
https://lists.sourceforge.net/lists/listinfo/bacula-users