Hi, John.
On Saturday, 12 June 2010 16:24:09 -0400,
John Drescher wrote:
> >> However, in the operating system I'm only seeing the tape drive,
> >> but not the autochanger:
> >>
> >>
> >> backup:~# cat /proc/scsi/scsi
> >> Attached devices:
> >> Host: scsi3 Channel: 00 Id: 00 Lun: 00
> >> Vendor: ATA Model: ST3160211AS Rev: 3.AA
> >> Type: Direct-Access ANSI SCSI revision: 05
> >>
> >>
> >> But I'm not seeing a /dev/st0 or /dev/nst0 device.
> > Now that I see, this has nothing to do with the tape drive:
> My guess is you do not have the sas driver loaded.
I forgot to comment this, but the SAS RAID controller card is recognized
by the operating system:
------------------------------------------------------------------------
ackup:~# lspci -vvv -s 02:00.0
02:00.0 RAID bus controller: Hewlett-Packard Company Smart Array G6 controllers
(rev 01)
Subsystem: Hewlett-Packard Company Smart Array P212
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at df400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at df3ff000 (64-bit, non-prefetchable) [size=4K]
Region 4: I/O ports at d800 [size=256]
Expansion ROM at df300000 [disabled] [size=512K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <1us, L1
<8us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x8, ASPM L0s, Latency L0
<512ns, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [ac] MSI-X: Enable+ Mask- TabSize=16
Vector table: BAR=0 offset=001c2000
PBA: BAR=0 offset=001c4000
Capabilities: [100] Advanced Error Reporting <?>
Kernel driver in use: cciss
Kernel modules: cciss
------------------------------------------------------------------------
This card uses the module 'cciss' which has been loaded by the kernel:
backup:~# lsmod | grep cciss
cciss 51620 0
scsi_mod 129548 3 sd_mod,cciss,libata
Thanks for your reply.
Regards,
Daniel
--
Fingerprint: BFB3 08D6 B4D1 31B2 72B9 29CE 6696 BF1B 14E6 1D37
Powered by Debian GNU/Linux Lenny - Linux user #188.598
signature.asc
Description: Digital signature
------------------------------------------------------------------------------
ThinkGeek and WIRED's GeekDad team up for the Ultimate
GeekDad Father's Day Giveaway. ONE MASSIVE PRIZE to the
lucky parental unit. See the prize list and enter to win:
http://p.sf.net/sfu/thinkgeek-promo _______________________________________________
Bacula-users mailing list
Bacula-users AT lists.sourceforge DOT net
https://lists.sourceforge.net/lists/listinfo/bacula-users
|
