On 2006-04-27 16:02, Arnd wrote:
Hello list,
I'm not sure if this is the right location to ask for help but I must
have a mistake somewhere and not able to get amanda running.
log.XXXXXXX.X:
--------------
DISK planner syse-s7010-002 /home/test
START planner date 20060427
WARNING planner tapecycle (7) <= runspercycle (7)
INFO planner Adding new disk syse-s7010-002:/home/test.
START driver date 20060427
STATS driver startup time 0.098
START taper datestamp 20060427 label DailySet105 tape 0
FAIL planner syse-s7010-002 /home/test 20060427 0 [disk /home/test, all
estimate failed]
FINISH planner date 20060427 time 1.060
WARNING driver WARNING: got empty schedule from planner
INFO taper tape DailySet105 kb 0 fm 0 [OK]
FINISH driver date 20060427 time 1.057
--------------
Remark: there is only one disk. So the "all estimate failed" message
that is triggered (because all of rest Amanda is supposed to do will
fail now too), is not as bad as it sounds. We just have to find the
reason why this /home/test fails to estimate.
Seconds remark: Did "amcheck" pass all tests? The error messages
by amcheck are much clearer and to the point.
I'm unable to get over this "all estimate failed" and I was even unable
to find any explanation on amanda.org about this error.
The according part in the amdump.1 file is:
--------------
...
SETTING UP FOR ESTIMATES...
planner: time 0.001: setting up estimates for syse-s7010-002:/home/test
syse-s7010-002:/home/test overdue 13266 days for level 0
setup_estimate: syse-s7010-002:/home/test: command 0, options: none
last_level -1 next_level0 -13266 level_days
0 getting estimates 0 (-2) -1 (-2) -1 (-2)
planner: time 0.001: setting up estimates took 0.000 secs
GETTING ESTIMATES...
driver: pid 1820 executable /usr/libexec/driver version 2.4.5p1
driver: tape size 204800
driver: send-cmd time 0.003 to taper: START-TAPER 20060427
reserving 0 out of 0 for degraded-mode dumps
planner: time 0.050: got partial result for host syse-s7010-002 disk
/home/test: 0 -> -2K, -1 -> -2K, -1 -> -2K
taper: pid 1821 executable taper version 2.4.5p1
...
--------------
I am wondering why there are negative results in this "estimate" process.
Seems to me like the client tried to estimate and failed completely.
E.g. you specified program DUMP (or omit the "program" parameter
from the dumptype which then defaults to DUMP), but there is suitable
dump program on the client. Amcheck would have told that.
--
Paul Bijnens, xplanation Technology Services Tel +32 16 397.511
Technologielaan 21 bus 2, B-3001 Leuven, BELGIUM Fax +32 16 397.512
http://www.xplanation.com/ email: Paul.Bijnens AT xplanation DOT com
***********************************************************************
* I think I've got the hang of it now: exit, ^D, ^C, ^\, ^Z, ^Q, ^^, *
* F6, quit, ZZ, :q, :q!, M-Z, ^X^C, logoff, logout, close, bye, /bye, *
* stop, end, F3, ~., ^]c, +++ ATH, disconnect, halt, abort, hangup, *
* PF4, F20, ^X^X, :D::D, KJOB, F14-f-e, F8-e, kill -1 $$, shutdown, *
* init 0, kill -9 1, Alt-F4, Ctrl-Alt-Del, AltGr-NumLock, Stop-A, ... *
* ... "Are you sure?" ... YES ... Phew ... I'm out *
***********************************************************************
|
