• Please help support our sponsors by considering their products and services.
    Our sponsors enable us to serve you with this high-speed Internet connection and fast webservers you are currently using at ADSM.ORG.
    They support this free flow of information and knowledge exchange service at no cost to you.

    Please welcome our latest sponsor Tectrade . We can show our appreciation by learning more about Tectrade Solutions
  • Community Tip: Please Give Thanks to Those Sharing Their Knowledge.

    If you receive helpful answer on this forum, please show thanks to the poster by clicking "LIKE" link for the answer that you found helpful.

  • Community Tip: Forum Rules (PLEASE CLICK HERE TO READ BEFORE POSTING)

    Click the link above to access ADSM.ORG Acceptable Use Policy and forum rules which should be observed when using this website. Violators may be banned from this website. This notice will disappear after you have made at least 3 posts.

3584 Library capacity increase

#1
Hi



I have just spent £10000 on the capacity increase for the 3584 library, this allows me to use the storage slot colums on the the door. Since doing this i have redifined the library within TSM however, i can only use two of the four colums on the the door. When runnin lable libvol etc the act log tells me the library is full (Its not)



Has anybody else had this problem? can you offer any advice?



Ive been ripped off!
 

putergal

ADSM.ORG Member
#2
I have a 3494 library and when adding new capacity we had to configure the robot to learn where the new slots were. I am not sure about the 3584, but it would seem that the libary would need to be reconfigured.

















<TABLE BORDER=0 ALIGN=CENTER WIDTH=85%><TR><TD><font class="pn-sub">Quote:</font><HR></TD></TR><TR><TD><FONT class="pn-sub"><BLOCKQUOTE>Hi



I have just spent £10000 on the capacity increase for the 3584 library, this allows me to use the storage slot colums on the the door. Since doing this i have redifined the library within TSM however, i can only use two of the four colums on the the door. When runnin lable libvol etc the act log tells me the library is full (Its not)



Has anybody else had this problem? can you offer any advice?



Ive been ripped off!

</BLOCKQUOTE></FONT></TD></TR><TR><TD><HR></TD></TR></TABLE>
 

DBRAD891

ADSM.ORG Member
#3
£10k for a microcode upgrade, good old IBM you get a 100+ addtional slots which are already in the 3584....



We have gone through this upgrade recently, and all we have to complete was an audit library and all the slots became available instantly.......Does the 3584 via the front panel or Web interface see the slots? Run a inventry on the library, then get TSM to audit....if you still can't see the additional slots call IBM out and get them to confirm that the Mircocode has been accepted properly



;)
 

Advertise at ADSM.ORG

If you are reading this, so are your potential customer. Advertise at ADSM.ORG right now.

UpCloud high performance VPS at $5/month

Get started with $25 in credits on Cloud Servers. You must use link below to receive the credit. Use the promo to get upto 5 month of FREE Linux VPS.

The Spectrum Protect TLA (Three-Letter Acronym): ISP or something else?

  • Every product needs a TLA, Let's call it ISP (IBM Spectrum Protect).

    Votes: 18 18.8%
  • Keep using TSM for Spectrum Protect.

    Votes: 58 60.4%
  • Let's be formal and just say Spectrum Protect

    Votes: 12 12.5%
  • Other (please comement)

    Votes: 8 8.3%

Forum statistics

Threads
31,635
Messages
134,820
Members
21,670
Latest member
crypticsh
Top