Re: [Veritas-bu] Restoring from Multiplexed Backup
2008-08-01 14:00:51
Nope, that’s the only way.
________________________________________________________
Curtis Preston | VP
Data Protection
GlassHouse Technologies, Inc.
T: +1 760 710 2004 | C: +1 760 419 5838 | F: +1 760 710 2009
cpreston AT glasshouse DOT com | www.glasshouse.com
Infrastructure :: Optimized
From: Jeremy Finn
[mailto:jeremy.finn AT gmail DOT com]
Sent: Friday, August 01, 2008
10:35 AM
To: Curtis Preston
Cc: smpt;
veritas-bu AT mailman.eng.auburn DOT edu
Subject: Re: [Veritas-bu]
Restoring from Multiplexed Backup
Curtis,
Thank you for your reply.
I have tried your suggestion and it is working. I see a slight performance increase
when doing the mpx restore now, which should translate to higher gains when
restoring more data.
One more question for everyone: I need to rename files as well. Is the best
option to use bprestore -R <renamefile> or is there another trick that works
better? Can I use the same rename file for each bprestore command or should I
make one for each stream?
Thanks again,
Jeremy
On Fri, Aug 1, 2008 at 1:02 PM, Curtis Preston <cpreston AT glasshouse DOT com>
wrote:
It's been a while since I tested this, but _I_ remember that if you wanted it to
restore the way he wants, you HAD to issue five different restores at the same
time and use the restore delay feature to start them at the same time. If
you just selected five directories, it did them one at a time. That's why
I always did my multi-filesystem restores as a loop
for I in /a /b /c /d /e
do
bprestore $I
done
________________________________________________________
Curtis
Preston | VP Data Protection
GlassHouse Technologies, Inc.
T: +1 760 710 2004 | C: +1 760 419 5838 | F: +1 760 710 2009
cpreston AT glasshouse DOT com
| www.glasshouse.com
Infrastructure :: Optimized
Do you select all mount points at the same
restore? If yes, then you will see only one job, but netbackup will
restore all files in one tape pass.
If you start 5 restores the you have to be
fast (every restore must start within 30 sec, by default). This can be changed
from master server properties.
stefanos
Hello,
I have a standard backup policy configured to stream five mount points to one
tape drive. This is working fine.
When I do the restore, I only see one stream restoring at a time. Is it
possible to restore the five streams of data from the multiplexed tape at the
same time?
Other backup softwarescan do this so I assume Netbackup can as well... if some
could please point me in the right direction it would be much appreciated.
My environment looks like this:
Master: Solaris 10 on SPARC
Media Server: HP-UX on PA-RISC
Source Client: HP-UX on PA-RISC
Target Client: HP-UX on PA-RISC
Multistream = 5
Multiplex = 5
One LTO-1 tape drive
Thank you in advance for any insights.
Jeremy
This email and any files transmitted with it are confidential and intended
solely for the use of the individual or entity to whom they are addressed. If
you have received this email in error please notify the system manager. This
message contains confidential information and is intended only for the
individual named. If you are not the named addressee you should not
disseminate, distribute or copy this e-mail.
This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this email in error please notify the system manager. This message contains confidential information and is intended only for the individual named. If you are not the named addressee you should not disseminate, distribute or copy this e-mail.
|
_______________________________________________
Veritas-bu maillist - Veritas-bu AT mailman.eng.auburn DOT edu
http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu
|
|
|