Hi all,
We have the following SAN environment :
Server Compaq running Windows 2000 SP2
HBA LP8000
Compaq SAN Swhitches and Router
Library: 2 TL891DLX + Expansion Unit + Data Unit -> configured as one unit
with 4 dlt drives and 52 tape slots.
TSM 4.2.1 (IP22393)
When we try any op read,write,audit lib,label,etc we get this
Tsm event :
11/30/2001 8:19:24 AM ADSMServer Error
(8300) 21 N/A
LABCORREIO TSM Server Error: Server: LABCORREIO_SERVER1 ANR8300E
I/O error on library TL891SAN (OP=8401C058, CC=205, KEY=FF, ASC=FF,
ASCQ=FF,~SENSE=**NONE**,~Description=SCSI adapter failure). Refer to Appendix
D in the 'Messages' manual for recommended action.
11/30/2001 8:17:32 AM ADSMServer Error
(8300) 21 N/A
LABCORREIO TSM Server Error: Server: LABCORREIO_SERVER1 ANR8300E
I/O error on library TL891SAN (OP=8401C058, CC=205, KEY=FF, ASC=FF,
ASCQ=FF,~SENSE=**NONE**,~Description=SCSI adapter failure). Refer to Appendix
D in the 'Messages' manual for recommended action.
11/30/2001 8:15:41 AM ADSMServer Error
(8300) 21 N/A
LABCORREIO TSM Server Error: Server: LABCORREIO_SERVER1 ANR8300E
I/O error on library TL891SAN (OP=8401C058, CC=205, KEY=FF, ASC=FF,
ASCQ=FF,~SENSE=**NONE**,~Description=SCSI adapter failure). Refer to Appendix
D in the 'Messages' manual for recommended action.
5/29/2001 9:13:09 AM ADSMServer Error (8300)
21 N/A
LABCORREIO TSM Server Error: Server: LABCORREIO_SERVER1 ANR8300E
I/O error on library TL891SAN (OP=8401C058, CC=205, KEY=FF, ASC=FF,
ASCQ=FF,~SENSE=**NONE**,~Description=SCSI adapter failure). Refer to Appendix
D in the 'Messages' manual for recommended action.
Adsmscsi event :
Dump Data: byte 0x2D=SRB Status, byte 0x2C=SCSI Status
11/30/2001 8:17:32 AM AdsmScsi Error None
1 N/A
LABCORREIO A non check condition error has occured on device
\Device\lb0.0.1.3 during Move Medium with completion code
DD_SCSI_ADAPTER_FAILURE.
Dump Data: byte 0x2D=SRB Status, byte 0x2C=SCSI Status
11/30/2001 8:15:41 AM AdsmScsi Error None
1 N/A
LABCORREIO A non check condition error has occured on device
\Device\lb0.0.1.3 during Move Medium with completion code
DD_SCSI_ADAPTER_FAILURE.
Dump Data: byte 0x2D=SRB Status, byte 0x2C=SCSI Status
5/29/2001 9:13:09 AM AdsmScsi Error None
1 N/A
LABCORREIO A non check condition error has occured on device
\Device\lb0.0.1.3 during Move Medium with completion code
DD_SCSI_ADAPTER_FAILURE.
Dump Data: byte 0x2D=SRB Status, byte 0x2C=SCSI Status
5/28/2001 6:10:11 PM AdsmScsi Error None
1 N/A
LABCORREIO A non check condition error has occured on device
\Device\lb0.0.1.3 during Move Medium with completion code
DD_SCSI_ADAPTER_FAILURE.
Dump Data: byte 0x2D=SRB Status, byte 0x2C=SCSI Status
5/28/2001 4:15:36 AM AdsmScsi Error None
1 N/A
LABCORREIO A non check condition error has occured on device
\Device\lb0.0.1.3 during Move Medium with completion code
DD_SCSI_ADAPTER_FAILURE.
Dump Data: byte 0x2D=SRB Status, byte 0x2C=SCSI Status
5/28/2001 4:10:44 AM AdsmScsi Error None
1 N/A
LABCORREIO A non check condition error has occured on device
\Device\lb0.0.1.3 during Move Medium with completion code
DD_SCSI_ADAPTER_FAILURE.
Compaq says that the HW is OK !
Does anyone know what is happening ? Any hint,similar environment working ? All
help is welcome. I know about APAR IC31466 but its not clear about the problem
(HW/Compaq or SW/Tivoli ?) and what are the solutions (patches,hw not
supported,etc).
Thanks in advance.
Paul Gondim van Dongen
Engenheiro de Sistemas
VANguard - Value Added Network guardians
http://www.vanguard-it.com.br
Fone: 55 81 3225-0353
-------------------------------------------------------------------
Este e-mail foi enviado pelo site da Nlink: http://www.nlink.com.br
Este e-mail foi enviado pelo site da Nlink: http://www.nlink.com.br
|
