mbriotto
ADSM.ORG Member
I have an IBM 3583 Library with FC connection via SDG with 3 tape drive and my data cartridge are 60 "IBM Totalstorage LTO Ultrim 100G" and 120 "Sony LTX 100G". I'm using win2k with TSM Server Ver 5.2.3.
IBM tapes work fine.
20 Sony tapes was faulty with error on write after 4 month.
IBM support says: "IBM tapes do not present errors, call Sony.
Sony says: "You are the only european customer with this problem, our media are not bad. Ask IBM"
The actlog is:
ANR8944E Hardware or media error on drive MT0.6.0.3
(mt0.6.0.3) (OP=WRITE, Error Number=23, CC=0, KEY=03,
ASC=0C, ASCQ=00, SENSE=71.00.03.00.00.00.00.1C.00.00.00.-
00.0C.00.06.00.40.02.00.00.00.02.00.00.00.00.00.00.00.19-
.00.00.4D.71.03.01.00.00.00.00.01.80.03.02.21.00.01.30.4-
9.42.4D.20.20.20.20.20.55.4C.54.33.35.38.30.2D.54.44.31.-
20.20.20.20.20.34.35.36.31.49.42.4D.20.20.20.20.20.00.55-
.4C.54.33.35.38.30.2D.54.44.31, Description=An
undetermined error has occurred). Refer to Appendix D in
the 'Messages' manual for recommended action. (PROCESS:
250)
ANR8359E Media fault detected on LTO volume D00088L1 in
drive MT0.6.0.3 (mt0.6.0.3) of library LB0.1.0.3.
(PROCESS: 250)
ANR1411W Access mode for volume D00088L1 now set to
"read-only" due to write error. (PROCESS: 250)
ANR0515I Process 250 closed volume D00088L1. (PROCESS:
250)
ANR8944E Hardware or media error on drive MT0.6.0.3
(mt0.6.0.3) (OP=OFFL, Error Number=23, CC=0, KEY=03,
ASC=0C, ASCQ=00, SENSE=71.00.03.00.00.00.00.1C.00.00.00.-
00.0C.00.06.00.40.02.00.00.00.02.00.00.00.00.00.00.00.19-
.00.00.4D.71.03.01.8E.35.00.00.8F.35.00.00.90.35.00.00.9-
1.35.00.00.91.35.00.00.FF.FF.FF.FF.FF.FF.FF.FF.17.30.00.-
DD.3A.22.02.40.E5.89.D8.50.A1.23.1C.0E.48.95.80.72.95.94-
.E0.A7.44.40.48.1C.71.3B.0B.91, Description=An
undetermined error has occurred). Refer to Appendix D in
the 'Messages' manual for recommended action. (PROCESS:
250)
ANR0513I Process 250 opened output volume 000001L1.
(PROCESS: 250)
ANR8950W Device mt0.6.0.3, volume D00088L1 has issued the
following Warning TapeAlert: The operation has stopped
because an error has occurred while reading or writing
data which the drive cannot correct. (PROCESS: 250)
ANR8948S Device mt0.6.0.3, volume D00088L1 has issued the
following Critical TapeAlert: The tape is from a faulty
batch or the tape drive is faulty: 1. Use a good tape to
test the drive. 2. If the problem persists, call the
tape drive supplier help line. (PROCESS: 250)
ANR8950W Device mt0.6.0.3, volume D00088L1 has issued the
following Warning TapeAlert: The tape drive may have a
hardware fault. Run extended diagnostics to verify and
diagnose the problem. Check the tape drive users manual
for device specific instruction on running extended
diagnostic tests. (PROCESS: 250)
ANR8469E Dismount of LTO volume D00088L1 from drive
MT0.6.0.3 (mt0.6.0.3) in library LB0.1.0.3 failed.
(PROCESS: 250)
ANR1410W Access mode for volume D00088L1 now set to
"unavailable". (PROCESS: 250)
ANR8475I Dismount of volume D00088L1 failed. It may still
be in the drive. (PROCESS: 250)
I updated all of the drivers: 3583, FC, Windows, TSM.
Does anybody else resolved similar problem?
IBM tapes work fine.
20 Sony tapes was faulty with error on write after 4 month.
IBM support says: "IBM tapes do not present errors, call Sony.
Sony says: "You are the only european customer with this problem, our media are not bad. Ask IBM"
The actlog is:
ANR8944E Hardware or media error on drive MT0.6.0.3
(mt0.6.0.3) (OP=WRITE, Error Number=23, CC=0, KEY=03,
ASC=0C, ASCQ=00, SENSE=71.00.03.00.00.00.00.1C.00.00.00.-
00.0C.00.06.00.40.02.00.00.00.02.00.00.00.00.00.00.00.19-
.00.00.4D.71.03.01.00.00.00.00.01.80.03.02.21.00.01.30.4-
9.42.4D.20.20.20.20.20.55.4C.54.33.35.38.30.2D.54.44.31.-
20.20.20.20.20.34.35.36.31.49.42.4D.20.20.20.20.20.00.55-
.4C.54.33.35.38.30.2D.54.44.31, Description=An
undetermined error has occurred). Refer to Appendix D in
the 'Messages' manual for recommended action. (PROCESS:
250)
ANR8359E Media fault detected on LTO volume D00088L1 in
drive MT0.6.0.3 (mt0.6.0.3) of library LB0.1.0.3.
(PROCESS: 250)
ANR1411W Access mode for volume D00088L1 now set to
"read-only" due to write error. (PROCESS: 250)
ANR0515I Process 250 closed volume D00088L1. (PROCESS:
250)
ANR8944E Hardware or media error on drive MT0.6.0.3
(mt0.6.0.3) (OP=OFFL, Error Number=23, CC=0, KEY=03,
ASC=0C, ASCQ=00, SENSE=71.00.03.00.00.00.00.1C.00.00.00.-
00.0C.00.06.00.40.02.00.00.00.02.00.00.00.00.00.00.00.19-
.00.00.4D.71.03.01.8E.35.00.00.8F.35.00.00.90.35.00.00.9-
1.35.00.00.91.35.00.00.FF.FF.FF.FF.FF.FF.FF.FF.17.30.00.-
DD.3A.22.02.40.E5.89.D8.50.A1.23.1C.0E.48.95.80.72.95.94-
.E0.A7.44.40.48.1C.71.3B.0B.91, Description=An
undetermined error has occurred). Refer to Appendix D in
the 'Messages' manual for recommended action. (PROCESS:
250)
ANR0513I Process 250 opened output volume 000001L1.
(PROCESS: 250)
ANR8950W Device mt0.6.0.3, volume D00088L1 has issued the
following Warning TapeAlert: The operation has stopped
because an error has occurred while reading or writing
data which the drive cannot correct. (PROCESS: 250)
ANR8948S Device mt0.6.0.3, volume D00088L1 has issued the
following Critical TapeAlert: The tape is from a faulty
batch or the tape drive is faulty: 1. Use a good tape to
test the drive. 2. If the problem persists, call the
tape drive supplier help line. (PROCESS: 250)
ANR8950W Device mt0.6.0.3, volume D00088L1 has issued the
following Warning TapeAlert: The tape drive may have a
hardware fault. Run extended diagnostics to verify and
diagnose the problem. Check the tape drive users manual
for device specific instruction on running extended
diagnostic tests. (PROCESS: 250)
ANR8469E Dismount of LTO volume D00088L1 from drive
MT0.6.0.3 (mt0.6.0.3) in library LB0.1.0.3 failed.
(PROCESS: 250)
ANR1410W Access mode for volume D00088L1 now set to
"unavailable". (PROCESS: 250)
ANR8475I Dismount of volume D00088L1 failed. It may still
be in the drive. (PROCESS: 250)
I updated all of the drivers: 3583, FC, Windows, TSM.
Does anybody else resolved similar problem?
