mupenx
ADSM.ORG Member
Is it possible to setup the TSM directly backup data to tape ??
If it possible is there any configuration should be done ?
thanks
If it possible is there any configuration should be done ?
thanks
-
-
Community Tip: Forum Rules (PLEASE CLICK HERE TO READ BEFORE POSTING)
Click the link above to access ADSM.ORG Acceptable Use Policy and forum rules which should be observed when using this website. Violators may be banned from this website. This notice will disappear after you have made at least 3 posts.
Direct to Tape Configuration
- Thread starter mupenx
- Start date
mupenx
ADSM.ORG Member
only do that ?? i think i already set things like that but not working at all...
sgabriel62
ADSM.ORG Senior Member
- Joined
- Apr 7, 2005
- Messages
- 1,356
- Reaction score
- 5
- Points
- 0
- Location
- Michigan
- Website
- www.sgsolutionsinc.com
please verify your config for us - also check your tape paths and keep your drives online. Verify your device class, management classes etc... Do full detail on each so you get a complete picture
mupenx
ADSM.ORG Member
this is the query from stgpool
Storage Device Estimated Pct Pct High Low Next Stora-
Pool Name Class Name Capacity Util Migr Mig Mig ge Pool
Pct Pct
----------- ---------- ---------- ----- ----- ---- --- -----------
ARCHIVEPOOL DISK 0.0 M 0.0 0.0 90 70
BACKUPPOOL DISK 0.0 M 0.0 0.0 0 0
DISKPOOL DISK 4.0 M 0.1 0.0 0 0
LTOPOOL1 LTOCLASS1 0.0 M 0.0 0.0 90 70
SPACEMGPOOL DISK 0.0 M 0.0 0.0 90 70
attached the query result devclass, drive, library, management class, path.
is it enough ??
Storage Device Estimated Pct Pct High Low Next Stora-
Pool Name Class Name Capacity Util Migr Mig Mig ge Pool
Pct Pct
----------- ---------- ---------- ----- ----- ---- --- -----------
ARCHIVEPOOL DISK 0.0 M 0.0 0.0 90 70
BACKUPPOOL DISK 0.0 M 0.0 0.0 0 0
DISKPOOL DISK 4.0 M 0.1 0.0 0 0
LTOPOOL1 LTOCLASS1 0.0 M 0.0 0.0 90 70
SPACEMGPOOL DISK 0.0 M 0.0 0.0 90 70
attached the query result devclass, drive, library, management class, path.
is it enough ??
BBB
ADSM.ORG Moderator
Post "q copy f=d"
And the include/exclude list for the node you are trying to get to go to tape (ie "q inclexcl" *on the client*)
You need to have the destination for the copygroup pointing at the tape storage pool.
And the include/exclude list for the node you are trying to get to go to tape (ie "q inclexcl" *on the client*)
You need to have the destination for the copygroup pointing at the tape storage pool.
dschulz
ADSM.ORG Member
Look to your PATH.TXT The path to your Drive is not Online.
Try to set these path Online to reach the Drive.
Try to set these path Online to reach the Drive.
gardenia
Active Newcomer
hi,
--->u might have defined a copy group in that specify the destination as your tapepool ." define copygroup domain_name policyset_name class_name destination=LTOPOOL" (or else)<B>
---->In the Diskpool ,set the highmig=0 and lowmig=0 "define stgpool diskpool higmig=0 lowmig=0 Nxtstgpool=LTOPOOL". the datas from the client starts to move to the diskpool once it checks the mig as 0 ,it will automatically starts migrating to the tapepool;
I think either of the step would help u out...
--->u might have defined a copy group in that specify the destination as your tapepool ." define copygroup domain_name policyset_name class_name destination=LTOPOOL" (or else)<B>
---->In the Diskpool ,set the highmig=0 and lowmig=0 "define stgpool diskpool higmig=0 lowmig=0 Nxtstgpool=LTOPOOL". the datas from the client starts to move to the diskpool once it checks the mig as 0 ,it will automatically starts migrating to the tapepool;
I think either of the step would help u out...
mupenx
ADSM.ORG Member
OK, thanks for the suggestion
