Re: [Networker] Unload failures with ADIC Scalar 1000 (DLT8000) on SAN using DDS
2003-11-21 14:13:58
We have 5 Scalar 1000's -
nw3 621A.00001 DLT8000 drives and 2 FCR250 routers
tlm 601A.00001 DLT8000 drives and FCR250 router
mse 621A.00001 LTO-1 drives and SNC3100 router
bc 621A.00001 LTO-1 drives and SNC3100 router
hbr 621A.00001 LTO-1 drives and SNC5100 router
thanks - John
-----Original Message-----
From: Bob Schuknecht [mailto:Bob_Schuknecht AT hilton DOT com]
Sent: Friday, November 21, 2003 10:28 AM
To: Legato NetWorker discussion; Ballinger, John M
Subject: RE: [Networker] Unload failures with ADIC Scalar 1000 (DLT8000)
on SAN using DDS
We have a similar setup as yours but our timers are not set anywhere
close to yours.
Eject 20
Cleaning 60
Unload 20
Load 20
Polling 3
Deposit 15
Withdrawal 15
Idle timeout 10
Another item to check is the firmware version loaded on the Scalar 1000.
We have two Scalar 1000s. The one that gives us less fits is version
3.00. The other one is at version 6.1.
-----Original Message-----
From: Ballinger, John M [mailto:john.ballinger AT PNL DOT GOV]
Sent: Sunday, November 16, 2003 12:25 AM
To: NETWORKER AT LISTMAIL.TEMPLE DOT EDU
Subject: [Networker] Unload failures with ADIC Scalar 1000 (DLT8000) on
SAN using DDS
Anyone have an idea what our problem might be?
We have an ADIC Scalar 1000 tape library using 2 FCR250's on a SAN.
One Solaris box is the NetWorker server and 3 other Solaris systems are
storage nodes.
Each of the 4 systems is on the SAN with a single HBA (all emulex
LP8000's) and we use persistent binding.
We continue to see unload failures of drives in the nw3 tape-library.
And we've set the timers for the jukebox as follows:
Eject sleep 120
Cleaning delay 300
Unload Sleep 60
Load Sleep 60
Port polling period 3
Deposit timeout 15
Withdraw timeout 15
Idle device timeout 10
nw3# nsrjb -HEv
setting verbosity level to `1'
hardware_reset:
Jukebox handle being opened at port [email protected]
hardware_reset:
Jukebox handle being closed at port [email protected]
Jukebox handle being opened at port [email protected]
box_inventory:
Jukebox handle being closed at port [email protected]
box_inventory_free:
Jukebox handle being opened at port [email protected]
box_comp_status():
box_comp_status_free():
box_comp_status():
box_comp_status_free():
box_comp_status():
box_comp_status_free():
box_comp_status():
box_comp_status_free():
box_comp_status():
box_comp_status_free():
box_comp_status():
box_comp_status_free():
box_comp_status():
box_comp_status_free():
Jukebox handle being closed at port [email protected]
Jukebox handle being opened at port [email protected]
Unloading jukebox: drive `rd=nw3sn2:/dev/rmt/1cbn' into
slot `19'
box_unload: unload failure detected - retrying
box_unload: retry: start time = 1068855935
box_unload: retry: sleeping 30
Time is ~4:26PM here..
Earlier we had a successfull reset of the library:
nsrjb -HEv
setting verbosity level to `1'
hardware_reset:
Jukebox handle being opened at port [email protected]
hardware_reset:
Jukebox handle being closed at port [email protected]
Jukebox handle being opened at port [email protected]
box_inventory:
Jukebox handle being closed at port [email protected]
box_inventory_free:
Jukebox handle being opened at port [email protected]
box_comp_status():
box_comp_status_free():
box_comp_status():
box_comp_status_free():
box_comp_status():
box_comp_status_free():
box_comp_status():
box_comp_status_free():
box_comp_status():
box_comp_status_free():
box_comp_status():
box_comp_status_free():
box_comp_status():
box_comp_status_free():
Jukebox handle being closed at port [email protected]
box_display: `' for drive `/dev/rmt/0cbn'
box_display: `' for drive `rd=nw3sn4:/dev/rmt/1cbn'
box_display: `' for drive `rd=nw3sn4:/dev/rmt/2cbn'
box_display: `' for drive `rd=nw3sn4:/dev/rmt/3cbn'
box_display: `' for drive `rd=nw3sn4:/dev/rmt/4cbn'
box_display: `' for drive `rd=nw3sn4:/dev/rmt/5cbn'
box_display: `' for drive `rd=nw3sn4:/dev/rmt/6cbn'
--
Note: To sign off this list, send a "signoff networker" command via
email
to listserv AT listmail.temple DOT edu or visit the list's Web site at
http://listmail.temple.edu/archives/networker.html where you can
also view and post messages to the list.
=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=
--
Note: To sign off this list, send a "signoff networker" command via email
to listserv AT listmail.temple DOT edu or visit the list's Web site at
http://listmail.temple.edu/archives/networker.html where you can
also view and post messages to the list.
=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=
|
|
|