On Fri, 1 Nov 2002 08:55:23 -0500, Jessica Kelley
<jessica.kelley AT ACTERNA DOT COM> wrote:
>Yesterday an ADIC Scalar 1000 tape library was connected via fibre channel
>(using Sun's fibre channel card) to a Sun E450 backup host running Solaris
>8. (This is the second ADIC Scalar 1000 library that's attached to this
>backup host.) The OS sees the new tape library and all of the tape drives
>but inquire and jbconfig fail to use the tape library. I'm running Legato
>Networker version 6.1.2.
>
># luxadm probe
>No Network Array enclosures found in /dev/es
>
>Found Fibre Channel device(s):
> Node WWN:10000060451630e7 Device Type:Tape device
> Logical Path:/dev/rmt/5n
> Logical Path:/dev/rmt/6n
> Logical Path:/dev/rmt/7n
> Logical Path:/dev/rmt/8n
> Logical Path:/dev/rmt/9n
> Logical Path:/dev/rmt/10n
># mt -f /dev/rmt/5cbn status
>Quantum DLT7000 tape drive:
> sense key(0x0)= No Additional Sense residual= 0 retries= 0
> file no= 0 block no= 0
># inquire -l
>
>-l flag found: searching all LUNs, which may take over 10 minutes per
>adapter
> for some fibre channel adapters. Please be patient.
>
>[email protected]:SEAGATE ST34371W SUN4.2G7462|Disk, /dev/rdsk/c0t0d0s2
>[email protected]:EXABYTE EXB-8505SMBANSH20098|Tape, /dev/rmt/0cbn
>[email protected]:TOSHIBA XM5701TASUN12XCD2395|CD-ROM, /dev/rdsk/c1t6d0s2
>[email protected]:FUJITSU MAB3091S SUN9.0G1505|Disk, /dev/rdsk/c2t0d0s2
>[email protected]:SEAGATE ST39204LCSUN9.0G4207|Disk, /dev/rdsk/c2t3d0s2
>[email protected]:FUJITSU MAB3091S SUN9.0G2107|Disk, /dev/rdsk/c3t0d0s2
>[email protected]:SEAGATE ST39204LCSUN9.0G4207|Disk, /dev/rdsk/c3t1d0s2
>[email protected]:QUANTUM DLT7000 2565|Tape, /dev/rmt/4cbn
>[email protected]:QUANTUM DLT7000 2561|Tape, /dev/rmt/1cbn
>[email protected]:ADIC Scalar 1000 3.00|Autochanger (Jukebox)
>[email protected]:QUANTUM DLT7000 2561|Tape, /dev/rmt/2cbn
>[email protected]:QUANTUM DLT7000 2565|Tape, /dev/rmt/3cbn
>
>Has anyone else seen this problem? Any suggestions on how to fix this
>problem?
I would guess that you don't have an entry for your HBA in the lus.conf
file. Is this card supported by Legato? You may need to raise a call with
Legato, but if the HBA is not on their supported list they won't help you.
I have absolutely no idea how to create new entries for lus.conf, anyone else?
--
Note: To sign off this list, send a "signoff" command via email
to listserv AT listmail.temple DOT edu or visit the list's Web site at
http://listmail.temple.edu/archives/networker.html where you can
also view and post messages to the list.
=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=
|
