Re: [Networker] Inquire fails to find fibre Channel connected Library

Instructions are at the top of /usr/kernel/drv/lus.conf.

Regards,
        /\/elson


On Fri, 1 Nov 2002, Davina Treiber wrote:

> On Fri, 1 Nov 2002 08:55:23 -0500, Jessica Kelley
> <jessica.kelley AT ACTERNA DOT COM> wrote:
>
> >Yesterday an ADIC Scalar 1000 tape library was connected via fibre channel
> >(using Sun's fibre channel card) to a Sun E450 backup host running Solaris
> >8.  (This is the second ADIC Scalar 1000 library that's attached to this
> >backup host.)  The OS sees the new tape library and all of the tape drives
> >but inquire and jbconfig fail to use the tape library.  I'm running Legato
> >Networker version 6.1.2.
> >
> ># luxadm probe
> >No Network Array enclosures found in /dev/es
> >
> >Found Fibre Channel device(s):
> >  Node WWN:10000060451630e7  Device Type:Tape device
> >    Logical Path:/dev/rmt/5n
> >    Logical Path:/dev/rmt/6n
> >    Logical Path:/dev/rmt/7n
> >    Logical Path:/dev/rmt/8n
> >    Logical Path:/dev/rmt/9n
> >    Logical Path:/dev/rmt/10n
> ># mt -f /dev/rmt/5cbn status
> >Quantum DLT7000 tape drive:
> >   sense key(0x0)= No Additional Sense   residual= 0   retries= 0
> >   file no= 0   block no= 0
> ># inquire -l
> >
> >-l flag found: searching all LUNs, which may take over 10 minutes per
> >adapter
> >        for some fibre channel adapters.  Please be patient.
> >
> >[email protected]:SEAGATE ST34371W SUN4.2G7462|Disk, /dev/rdsk/c0t0d0s2
> >[email protected]:EXABYTE EXB-8505SMBANSH20098|Tape, /dev/rmt/0cbn
> >[email protected]:TOSHIBA XM5701TASUN12XCD2395|CD-ROM, /dev/rdsk/c1t6d0s2
> >[email protected]:FUJITSU MAB3091S SUN9.0G1505|Disk, /dev/rdsk/c2t0d0s2
> >[email protected]:SEAGATE ST39204LCSUN9.0G4207|Disk, /dev/rdsk/c2t3d0s2
> >[email protected]:FUJITSU MAB3091S SUN9.0G2107|Disk, /dev/rdsk/c3t0d0s2
> >[email protected]:SEAGATE ST39204LCSUN9.0G4207|Disk, /dev/rdsk/c3t1d0s2
> >[email protected]:QUANTUM DLT7000         2565|Tape, /dev/rmt/4cbn
> >[email protected]:QUANTUM DLT7000         2561|Tape, /dev/rmt/1cbn
> >[email protected]:ADIC    Scalar 1000     3.00|Autochanger (Jukebox)
> >[email protected]:QUANTUM DLT7000         2561|Tape, /dev/rmt/2cbn
> >[email protected]:QUANTUM DLT7000         2565|Tape, /dev/rmt/3cbn
> >
> >Has anyone else seen this problem?  Any suggestions on how to fix this
> >problem?
>
> I would guess that you don't have an entry for your HBA in the lus.conf
> file. Is this card supported by Legato? You may need to raise a call with
> Legato, but if the HBA is not on their supported list they won't help you.
>
> I have absolutely no idea how to create new entries for lus.conf, anyone else?
>
> --
> Note: To sign off this list, send a "signoff" command via email
> to listserv AT listmail.temple DOT edu or visit the list's Web site at
> http://listmail.temple.edu/archives/networker.html where you can
> also view and post messages to the list.
> =*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=
>

--
~~ ** ~~  If you didn't learn anything when you broke it the 1st ~~ ** ~~
                        time, then break it again.

--
Note: To sign off this list, send a "signoff" command via email
to listserv AT listmail.temple DOT edu or visit the list's Web site at
http://listmail.temple.edu/archives/networker.html where you can
also view and post messages to the list.
=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=