Hi,
this is the qlogic driver version:
[ 1.348682] qla2xxx [0000:07:00.0]-00fa:1: QLogic Fibre Channed HBA Driver: 8.03.07.12-k.
[ 1.348686] qla2xxx [0000:07:00.0]-00fb:1: QLogic QLE2562 - QLogic 8Gb FC Dual-port HBA for System x.
[ 1.348699] qla2xxx [0000:07:00.0]-00fc:1: ISP2532: PCIe (2.5GT/s x8) @ 0000:07:00.0 hdma+ host#=1 fw=5.06.05 (90d5).
[ 1.348768] qla2xxx [0000:07:00.1]-001d: : Found an ISP2532 irq 19 iobase 0xffffc90000c68000.
[ 1.348949] qla2xxx 0000:07:00.1: irq 44 for MSI/MSI-X
[ 1.348956] qla2xxx 0000:07:00.1: irq 45 for MSI/MSI-X
[ 1.349023] qla2xxx [0000:07:00.1]-0040:2: Configuring PCI space...
[ 1.349028] qla2xxx 0000:07:00.1: setting latency timer to 64
[ 1.361424] qla2xxx [0000:07:00.1]-0061:2: Configure NVRAM parameters...
[ 1.369088] qla2xxx [0000:07:00.1]-0078:2: Verifying loaded RISC code...
[ 1.369131] qla2xxx [0000:07:00.1]-0092:2: Loading via request-firmware.
[ 1.400994] qla2xxx [0000:07:00.1]-00c0:2: Allocate (64 KB) for FCE...
[ 1.401064] qla2xxx [0000:07:00.1]-00c3:2: Allocated (64 KB) EFT ...
[ 1.401150] qla2xxx [0000:07:00.1]-00c5:2: Allocated (1350 KB) for firmware dump.
[ 1.405503] scsi2 : qla2xxx
[ 1.405763] qla2xxx [0000:07:00.1]-00fa:2: QLogic Fibre Channed HBA Driver: 8.03.07.12-k.
[ 1.405767] qla2xxx [0000:07:00.1]-00fb:2: QLogic QLE2562 - QLogic 8Gb FC Dual-port HBA for System x.
[ 1.405779] qla2xxx [0000:07:00.1]-00fc:2: ISP2532: PCIe (2.5GT/s x8) @ 0000:07:00.1 hdma+ host#=2 fw=5.06.05 (90d5).
......
[ 2.928979] scsi 1:0:0:0: Sequential-Access IBM ULT3580-TD3 93GP PQ: 0 ANSI: 3
[ 2.935530] st: Version 20101219, fixed bufsize 32768, s/g segs 256
[ 2.935861] st 1:0:0:0: Attached scsi tape st0
[ 2.935864] st 1:0:0:0: st0: try direct i/o: yes (alignment 4 B)
[ 3.939166] qla2xxx [0000:07:00.1]-500a:2: LOOP UP detected (8 Gbps).
[ 3.997944] scsi 2:0:0:0: Sequential-Access IBM ULT3580-TD5 C7RC PQ: 0 ANSI: 6
[ 4.000531] scsi 2:0:0:1: Medium Changer IBM 03584L32 B570 PQ: 0 ANSI: 6
[ 4.012583] st 2:0:0:0: Attached scsi tape st1
[ 4.012586] st 2:0:0:0: st1: try direct i/o: yes (alignment 4 B)
[ 4.013947] osst :I: Tape driver with OnStream support version 0.99.4
[ 4.013948] osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
[ 4.014691] SCSI Media Changer driver v0.25
[ 4.016286] ch0: type #1 (mt): 0x1+2 [medium transport]
[ 4.016289] ch0: type #2 (st): 0x401+1601 [storage]
[ 4.016291] ch0: type #3 (ie): 0x301+10 [import/export]
[ 4.016293] ch0: type #4 (dt): 0x101+2 [data transfer]
[1:0:0:0] tape IBM ULT3580-TD3 93GP /dev/st0
[2:0:0:0] tape IBM ULT3580-TD5 C7RC /dev/st1
[2:0:0:1] mediumx IBM 03584L32 B570 /dev/sch0
Some times the reset hapends whwn a few MBs are written others after a couple of hundred MBs but only when we use the LTO5 ([2:0:0:0] tape IBM ULT3580-TD5 C7RC /dev/st1 ) the LT03 always works grate.