Hi,
i just got it back half working :-(

dmesg | grep 2:0:1:1
[   79.677949] scsi 2:0:1:1: Medium Changer    NEC      T40A2           
0005 PQ: 0 ANSI: 2
[   80.449402] ch 2:0:1:1: Attached scsi changer ch1
[   80.449402] ch 2:0:1:1: Attached scsi generic sg6 type 8
[13387.819021] scsi 2:0:1:1: Medium Changer    NEC      T40A2           
0005 PQ: 0 ANSI: 2
[13388.191786] ch 2:0:1:1: Attached scsi changer ch1
[13388.191786] ch 2:0:1:1: Attached scsi generic sg6 type 8


if i run mtx -f $device status

i'll gett following messages
mtx -f /dev/sg3 status

mtx: Request Sense: Long Report=yes
mtx: Request Sense: Valid Residual=no
mtx: Request Sense: Error Code=70 (Current)
mtx: Request Sense: Sense Key=Illegal Request
mtx: Request Sense: FileMark=no
mtx: Request Sense: EOM=no
mtx: Request Sense: ILI=no
mtx: Request Sense: Additional Sense Code = 24
mtx: Request Sense: Additional Sense Qualifier = 00
mtx: Request Sense: Field in Error = 05
mtx: Request Sense: BPV=yes
mtx: Request Sense: Error in CDB=yes
mtx: Request Sense: SKSV=yes
mtx: Request Sense: Field Pointer = 00 02
Mode sense (0x1A) for Page 0x1D failed
mtx: Request Sense: Long Report=yes
mtx: Request Sense: Valid Residual=no
mtx: Request Sense: Error Code=70 (Current)
mtx: Request Sense: Sense Key=Illegal Request
mtx: Request Sense: FileMark=no
mtx: Request Sense: EOM=no
mtx: Request Sense: ILI=no
mtx: Request Sense: Additional Sense Code = 20
mtx: Request Sense: Additional Sense Qualifier = 00
mtx: Request Sense: Field in Error = 00
mtx: Request Sense: BPV=no
mtx: Request Sense: Error in CDB=yes
mtx: Request Sense: SKSV=yes
mtx: Request Sense: Field Pointer = 00 00
READ ELEMENT STATUS Command Failed


mtx -f /dev/sg4 status

mtx: Request Sense: Long Report=yes
mtx: Request Sense: Valid Residual=no
mtx: Request Sense: Error Code=70 (Current)
mtx: Request Sense: Sense Key=Illegal Request
mtx: Request Sense: FileMark=no
mtx: Request Sense: EOM=no
mtx: Request Sense: ILI=no
mtx: Request Sense: Additional Sense Code = 20
mtx: Request Sense: Additional Sense Qualifier = 00
mtx: Request Sense: Field in Error = 00
mtx: Request Sense: BPV=no
mtx: Request Sense: Error in CDB=yes
mtx: Request Sense: SKSV=yes
mtx: Request Sense: Field Pointer = 00 00
READ ELEMENT STATUS Command Failed

also on bat, the slots for the lto4 are not shown.

slowly this become a little bit critical

thanks
andre


On 25.05.2011 17:36, Mauro Colorio wrote:
> try this
>
> dmesg | grep 2:0:1:1
>
> it will tell you the name of the device where the loaders is attached
> (sg3 in my case)
> then
>
> mtx -f /dev/sg3 status
>
> if it works check ur config files
>
> Mauro
>
> ------------------------------------------------------------------------------
> vRanger cuts backup time in half-while increasing security.
> With the market-leading solution for virtual backup and recovery, 
> you get blazing-fast, flexible, and affordable data protection.
> Download your free trial now. 
> http://p.sf.net/sfu/quest-d2dcopy1
> _______________________________________________
> Bacula-users mailing list
> Bacula-users AT lists.sourceforge DOT net
> https://lists.sourceforge.net/lists/listinfo/bacula-users

------------------------------------------------------------------------------
vRanger cuts backup time in half-while increasing security.
With the market-leading solution for virtual backup and recovery, 
you get blazing-fast, flexible, and affordable data protection.
Download your free trial now. 
http://p.sf.net/sfu/quest-d2dcopy1
_______________________________________________
Bacula-users mailing list
Bacula-users AT lists.sourceforge DOT net
https://lists.sourceforge.net/lists/listinfo/bacula-users