RE: [NV-L] Making a smart set based on ip's
2007-05-22 16:37:55
No restart of nvcorrd, or any other daemon, required when creating SmartSets. SmartSets are dynamic collections, so rules that are running will see all additions/removals from a SmartSet as they occur.
However, when creating a *new* SmartSet, it does need to be activated using the NetView interface.
Regards,
Greg Keetch
IT Specialist (Advisor), Network Services
Network Management Tools Specialist
Information Technology Services Americas (ITSA), Global Services, IBM Canada
"Kain, Becki \(B.\)" <bkain1 AT ford DOT com>
"Kain, Becki \(B.\)" <bkain1 AT ford DOT com>
Sent by: nv-l-bounces AT lists.ca.ibm DOT com
05/22/2007 12:50 PM
Please respond to
Tivoli NetView Discussions <nv-l AT lists.ca.ibm DOT com> |
|
|
do you need to restart nvcorrd if you use the smartset editor to do that?
thanks!
From: nv-l-bounces AT lists.ca.ibm DOT com [mailto:nv-l-bounces AT lists.ca.ibm DOT com] On Behalf Of Leslie Clark
Sent: Tuesday, May 22, 2007 10:55 AM
To: Tivoli NetView Discussions
Subject: Re: [NV-L] Making a smart set based on ip's
Look at the object info for a node. Nodes don't have a field 'IP Address'. That's an attribute of an interface. So you are getting a list of Selection Names of interfaces or Networks.
Nodes do have a field called 'SNMP ipAddress'.
Cordially,
Leslie A. Clark
IT Services Specialist, Network Mgmt
Information Technology Services Americas
IBM Global Services
(248) 552-4968 Voicemail, Fax, Pager
"Kain, Becki \(B.\)" <bkain1 AT ford DOT com>
Sent by: nv-l-bounces AT lists.ca.ibm DOT com
05/22/2007 09:51 AM
Please respond to
Tivoli NetView Discussions <nv-l AT lists.ca.ibm DOT com> |
|
To | "Tivoli NetView Discussions" <nv-l AT lists.ca.ibm DOT com> |
cc | |
Subject | [NV-L] Making a smart set based on ip's |
|
I tried making a smartset based on ip's:
nvUtil e '("IP Address" ~ "19.39.*.*")'
But the results that I get are not nodes but something else:
sdg100344q3b1.itek.ford.com:19.39.25.75
sdg100g3tfmb1.itek.ford.com:19.39.40.103
SEP001380AD917D.itek.ford.com:19.39.50.110
How do I make a smartset, based on a range of ip's, AND get actual nodes in it? Thanks in advance
_______________________________________________
NV-L mailing list
NV-L AT lists.ca.ibm DOT com
Unsubscribe:NV-L-leave AT lists.ca.ibm DOT com
http://lists.ca.ibm.com/mailman/listinfo/nv-l (Browser access limited to internal IBM'ers only)_______________________________________________
NV-L mailing list
NV-L AT lists.ca.ibm DOT com
Unsubscribe:NV-L-leave AT lists.ca.ibm DOT com
http://lists.ca.ibm.com/mailman/listinfo/nv-l (Browser access limited to internal IBM'ers only)
_______________________________________________
NV-L mailing list
NV-L AT lists.ca.ibm DOT com
Unsubscribe:NV-L-leave AT lists.ca.ibm DOT com
http://lists.ca.ibm.com/mailman/listinfo/nv-l (Browser access limited to
internal IBM'ers only)
|
|
|