I too have never seen a long name on a map (and I have seen a lot of
maps) except sometimes on a loopback subnet in V5. Yes, a missing
reverse lookup will causes problems, but they are usually worse problems
than a missing label, so I always address that thoroughly right up front.
If the DNS cannot provide two-way lookup, I say ditch the DNS. At current
maintenance levels I have seen very good updates to the map after updating
name resolution (mostly /etc/hosts in my case). I still see a few of those
deals where the Selection Name stays the address, but the IP Hostname
and the label are names. I either delete and rediscover them, or use
the context menu edit to switch the Selection Name to the name name.
Actually when the name comes along later I prefer to rediscover. This is
because if you don't, the Selection Name of the interfaces no longer
matches the Selection Name of the node. That match can come in handy.
My two cents...
Cordially,
Leslie A. Clark
IBM Global Services - Systems Mgmt & Networking
Detroit
"ANDERSON, Peter" <panderson AT westpac.com DOT au>@tkg.com on 03/13/2001
07:34:43
PM
Please respond to IBM NetView Discussion <nv-l AT tkg DOT com>
Sent by: owner-nv-l AT tkg DOT com
To: IBM NetView Discussion <nv-l AT tkg DOT com>
cc:
Subject: RE: [NV-L] Fully Qualified Hostnames
Just to be difficult, I always get the short name, and most of our devices
have forward and reverse lookups in DNS.
What P's me off is that the label doesn't get updated if the reverse entry
wasn't in DNS, but was later. In that scenario, the object name gets
changed to the FQDN but the map label stays as the IP address.
Leslie Clark seems to think this is normal though. (Am I correct??)
Regards,
Peter Anderson
Senior Communications Analyst
Any views or opinions presented are solely those of the author and do
not necessarily represent those of Westpac Banking Corporation.
-----Original Message-----
From: Treptow, Craig [mailto:Treptow.Craig AT principal DOT com]
Sent: Wednesday, March 14, 2001 4:03 AM
To: 'IBM NetView Discussion'
Subject: RE: [NV-L] Fully Qualified Hostnames
I think this is just a question of how you resolve your names. If my
devices have reverse DNS entries, then they get the FQDN in the Netview
map.
If not, they will get a shorter name, probably based on how the device is
configured, or sometimes no name at all, just an IP address.
> -----Original Message-----
> From: danny AT uk.ibm DOT com [mailto:danny AT uk.ibm DOT com]
> Sent: Tuesday, March 13, 2001 10:32 AM
> To: nv-l AT tkg DOT com
> Subject: [NV-L] Fully Qualified Hostnames
>
>
>
>
> Question number two of the day.
>
> Can I make NetView display the fully qualified Hostname of a
> device rather
> than the bit before the first "."?
>
> I have been trawling the manuals and on-line reference
> information to find
> out how to answer this, so I hope I haven't missed something really
> obvious:
>
> I did find one bit of information that said to put the fully
> qualified name
> in to a local /etc/hosts file and set hosts=local,bind in
> /etc/netsvc.conf.
> However, this requires a long hosts file in my case, which pretty much
> obviates DNS and will require a lot of management.
>
> What I want is a flag I can set somewhere!
>
> Here's hoping!
>
> Danny Williams
> Tivoli & AIX Specialist
> IBM Global Services - Integrated Technology Services
> mailto:danny AT uk.ibm DOT com
> Tel: 665520 (01926-465520) -- MOBX: 275520 (07967-275520)
>
>
> ______________________________________________________________
> ___________
> NV-L List information and Archives: http://www.tkg.com/nv-l
>
_________________________________________________________________________
NV-L List information and Archives: http://www.tkg.com/nv-l
_________________________________________________________________________
NV-L List information and Archives: http://www.tkg.com/nv-l
|
