Yes, I like slick too but sometimes when it's something you're only doing once
or twice for testing purposes and don't need it on an ongoing basis then brute
force methods are adequate.
Dave Werth
Garmin AT, Inc.
Salem, Oregon
-----Original Message-----
From: EMC NetWorker discussion [mailto:NETWORKER AT LISTSERV.TEMPLE DOT EDU] On
Behalf Of George Sinclair
Sent: Wednesday, October 06, 2010 3:31 PM
To: NETWORKER AT LISTSERV.TEMPLE DOT EDU
Subject: Re: [Networker] How to find a piece of a save set that spans?
Werth, Dave wrote:
> George,
>
> I don't know about how you can determine ahead of time what directories will
> span multiple volumes but you can certainly go into Recover and select a
> directory to recover then check the "Show required volumes" display to see if
> in fact it does span volumes. I don't imagine it would take too long to find
> one that did (but then what do I know?).
Yes, that's exactly what I'm looking for: a way to determine which
directories did in fact span tapes, NOT which ones will span tapes. So,
this is an "after the fact" question. I can certainly do as you
mentioned but was looking for a slick way to determine this without
trial and error?
Some of the save sets have a small number of top level sub-directories
so it won't take too long to find one that spans, but most of the save
sets have a lot of top level sub-directories, so that will take much
longer. Obviously, at least one of them must span two tapes.
George
>
> Dave Werth
> Garmin AT, Inc.
> Salem, Oregon
> -----Original Message-----
> From: EMC NetWorker discussion [mailto:NETWORKER AT LISTSERV.TEMPLE DOT EDU]
> On Behalf Of George Sinclair
> Sent: Wednesday, October 06, 2010 3:08 PM
> To: NETWORKER AT LISTSERV.TEMPLE DOT EDU
> Subject: [Networker] How to find a piece of a save set that spans?
>
> Hi,
>
> We have 19 save sets that we've just backed up. These have also been
> cloned. Each of these save sets is 1+ TB and consist of a number of
> smaller sized sub-directories, e.g. 300 KB, 2.4 GB, 19 GB, etc. The tape
> pool is indexed. All of these save sets span multiple tapes (minimally
> 3-4 tapes) as they were multiplexed together (parallelism=4) during backup.
>
> I'd like to run a browseable recover test (nwrecover or CLI recover) on
> a couple of random sub-directories from each save set, but I'd like
> to also pick a few that span at least two tapes. I don't want to recover
> the whole save set, however, as these are all very large.
>
> Is there a way I can determine which directories span two tapes?
>
> Will I have to just select random directories, using nwrecover or CLI
> recover, until I find one that shows two volumes required?
>
> Thanks.
>
> George
>
> --
> George Sinclair
> Voice: (301) 713-3284 x210
> - The preceding message is personal and does not reflect any official or
> unofficial position of the United States Department of Commerce -
> - Any opinions expressed in this message are NOT those of the US Govt. -
>
> To sign off this list, send email to listserv AT listserv.temple DOT edu and
> type "signoff networker" in the body of the email. Please write to
> networker-request AT listserv.temple DOT edu if you have any problems with
> this list. You can access the archives at
> http://listserv.temple.edu/archives/networker.html or
> via RSS at http://listserv.temple.edu/cgi-bin/wa?RSS&L=NETWORKER
>
>
> This e-mail and any attachments may contain confidential material for the
> sole use of the intended recipient. If you are not the intended recipient,
> please be aware that any disclosure, copying, distribution or use of this
> e-mail or any attachment is prohibited. If you have received this e-mail in
> error, please contact the sender and delete all copies.
>
> Thank you for your cooperation.
>
>
--
George Sinclair
Voice: (301) 713-3284 x210
- The preceding message is personal and does not reflect any official or
unofficial position of the United States Department of Commerce -
- Any opinions expressed in this message are NOT those of the US Govt. -
To sign off this list, send email to listserv AT listserv.temple DOT edu and
type "signoff networker" in the body of the email. Please write to
networker-request AT listserv.temple DOT edu if you have any problems with this
list. You can access the archives at
http://listserv.temple.edu/archives/networker.html or
via RSS at http://listserv.temple.edu/cgi-bin/wa?RSS&L=NETWORKER
To sign off this list, send email to listserv AT listserv.temple DOT edu and
type "signoff networker" in the body of the email. Please write to
networker-request AT listserv.temple DOT edu if you have any problems with this
list. You can access the archives at
http://listserv.temple.edu/archives/networker.html or
via RSS at http://listserv.temple.edu/cgi-bin/wa?RSS&L=NETWORKER
|
