Thank a lot for yours help.
I download the template for /etc/stinit.def from Legato site and also try to
use ibmtool for testing all Environment and also check settings of CDI for each
device. I will write back with my result
Antonio
-----Messaggio originale-----
Da: Warren Sturm [mailto:wrsturm AT mtroyal DOT ca]
Inviato: giovedì 24 febbraio 2005 16.15
A: Antonio Ettorre
Oggetto: Re: [Networker] scsi timeout on RH AS 2.1
I "think" it is the common device interface. It is set/unset in the GUI
in Menu->Devices and then you choose the device to check. We have had a
problem for the last couple of months with just these sort of errors
until we turned off CDI last week. CDI was introduced sometime in the
7.1.x timeframe, I think. You may also want to watch
your /etc/stinit.def if you run into a problem with tape positioning by
record once your tape drives settle down. There is a template on the
legato site.
On Thu, 2005-24-02 at 15:04 +0100, Antonio Ettorre wrote:
> Yes,
> I have some trouble on /dev/nst0 and /dev/nst1.
> And what is exactly CDI?
>
>
> On Wed, 23 Feb 2005 19:37:21 +0100, Petr Hanzlík <phanzlik AT coma DOT cz>
> wrote:
> >
> > Hi,
> >
> > have you the same trouble on /dev/nst0 ?
> > I have the same problem. Please verify your configuration of jukebox and run
> > jbconfig again.
> > Please, verify that you select good name device " /dev/nst0 or /dev/nst1 "
> > as first tape and good name device as second tape.
> >
> > ofcourse, whether device /dev/nst0 works correctly, verify the device
> > /dev/nst1 with other tools, mt, ltotool, ibmtool, or tar.
> >
> > Petr Hanzlík
> > COMA ZÁLOHOVACÍ SYSTÉMY a.s.
> > Vítkovická 1
> > Ostrava 1 702 00
> > Czech Republic
> > Tel.: ++420-59-6656377
> > Fax.: ++420-59-6656668
> > mailto:phanzlik AT coma DOT cz
> > mailto:726816 AT sms.eurotel DOT cz
> > http://www.coma.cz/
> > http://www.e-commercegroup.cz
> >
> >
> >
> >
> > Antonio Ettorre <vot4anto AT GMAIL DOT COM>
> > Odeslal: Legato NetWorker discussion <NETWORKER AT LISTSERV.TEMPLE DOT EDU>
> >
> > 23.02.2005 18:03
> > Odpovězte prosím uživateli Legato NetWorker discussion; Odpovězte prosím
> > uživateli Antonio Ettorre
> > Komu: NETWORKER AT LISTSERV.TEMPLE DOT EDU
> > Kopie:
> > Předmět: scsi timeout on RH AS 2.1
> >
> >
> >
> > Hi to all,
> >
> > I have a problem with scsi on Linux server, from the begin,The environment
> > is so configured:
> >
> >
> >
> > -library ADIC Scalar 24 with 2 drive IBM LTO Ultrium - TD1
> >
> >
> >
> > -Networker Server IBM X345 with Linux Red Hat Advanced Server 2.1 (kernel
> > 2.4.9-e.27smp)
> >
> >
> >
> > -Networker Client IBM X345 with Linux Red Hat Advanced Server 2.1 - Oracle 9
> > - module Legato for oracle 4.1
> >
> >
> >
> > He is able to perform regularly the backup of all the client except the
> > server.
> >
> > When he start manual or scheduled backup of data on the backup server,
> >
> > after some minutes the machine goes in an hang state.
> >
> > The available RAM pass from 1,5 GB to few MB.
> >
> > The saveset fails with error message "scsi : aborting command due to timeout
> > : pid 0, scsi0, channel
> >
> > 0, id 1, lun 0 Write (6) 01 00 ".
> >
> >
> >
> > What I did see is in the daemon.log is the following:
> >
> >
> >
> > 12/07/04 13:47:02 nsrd: media warning: /dev/nst1 reading: Input/output error
> >
> > 12/07/04 13:47:13 nsrd: media warning: /dev/nst1 reading: Tape label read
> > for volume ? in pool ?, is not recognised by Networker: Input/output error
> >
> > 12/07/04 13:49:50 nsrd: media warning: /dev/nst1 reading: Input/output error
> >
> > 12/07/04 13:50:01 nsrd: media warning: /dev/nst1 reading: Tape label read
> > for volume ? in pool ?, is not recognised by Networker: Input/output error
> >
> > 12/07/04 14:35:56 nsrd: media warning: /dev/nst0 reading: Input/output error
> >
> > 12/08/04 21:31:52 nsrd: media notice: Volume "009" on device "/dev/nst1":
> > Cannot decode block. Verify the device configuration. Tape positioning by
> > record is disabled.
> >
> > 12/08/04 21:32:49 nsrd: media warning: /dev/nst1 reading: fsr 11677 read:
> > Input/output error
> >
> > 12/10/04 22:03:30 nsrd: media warning: /dev/nst1 reading: fsr 1113 read:
> > Input/output error
> >
> > 12/13/04 00:29:08 nsrd: media warning: /dev/nst1 writing: Input/output
> > error, at file 281 record 14705
> >
> >
> >
> >
> >
> > Any suggest?
> >
> > Many thanks
> >
> > Antonio
> >
> >
> > --
> > Note: To sign off this list, send a "signoff networker" command via email
> > to listserv AT listserv.temple DOT edu or visit the list's Web site at
> > http://listserv.temple.edu/archives/networker.html where you can
> > also view and post messages to the list. Questions regarding this list
> > should be sent to stan AT temple DOT edu
> > =*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=
> >
>
> --
> Note: To sign off this list, send a "signoff networker" command via email
> to listserv AT listserv.temple DOT edu or visit the list's Web site at
> http://listserv.temple.edu/archives/networker.html where you can
> also view and post messages to the list. Questions regarding this list
> should be sent to stan AT temple DOT edu
> =*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=
--
Note: To sign off this list, send a "signoff networker" command via email
to listserv AT listserv.temple DOT edu or visit the list's Web site at
http://listserv.temple.edu/archives/networker.html where you can
also view and post messages to the list. Questions regarding this list
should be sent to stan AT temple DOT edu
=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=
|
