In Legato licensing world you UNIX and Linux.
So, if your server is on Linux to backup the UNIX
client you need UNIX clientpak.  Grab the media
kit and temp enabler from there until you buy one.
 
Cheers,
.c

        -----Original Message----- 
        From: Legato NetWorker discussion on behalf of David De Maeyer 
        Sent: Mon 20/09/2004 14:54 
        To: NETWORKER AT LISTMAIL.TEMPLE DOT EDU 
        Cc: 
        Subject: [Networker] RAP error: ClientPaks for UNIX/NSR enabler does 
not exist in the system
        
        

        Hi all,
        
        I'm facing a strange problem. I want to take a full backup of one of
        our server (running Solaris 8). Backup is to be done on disk (RAID).
        I've defined a new client (the server we want to backup), create a
        specific group for such manual full backup. No problem.
        
        But things go wrong once I start the group. The group starts with one
        client but dies immediately after the start. Savegroup notification
        says that there is no enable code existing in the system! I've checked
        the license and we have a NetWare ClientPack, a UNIX NetWorker (Network
        Edition with 10 clients), 3 NetWorker Client Connections and finally a
        DiskBackup enabler. All packs are properly enabled and authenticated
        (I've check all of them). See under.
        
        Date: 20 September 2004 14:14:14 GMT+02:00
        Subject: disco.ruc.dk's savegroup completion
        
        NetWorker savegroup: (alert) full on RAID completed, total 2 client(s),
        0 Hostname(s) Unresolved, 1 Failed, 1 Succeeded. (CLIENT Failed)
        Start time:   Mon Sep 20 14:14:05 2004
        End time:     Mon Sep 20 14:14:14 2004
        
        --- Unsuccessful Save Sets ---
        
        * CLIENT:/ 1 retry attempted
           CLIENT:/: No full backups of this save set were found in the media
        database; performing a full backup
        * CLIENT:/ save: RAP error: ClientPaks for UNIX/NSR enabler does not
        exist in the system
        * CLIENT:/ save: Cannot open save session with SERVER
        ...
        
        nsrlic reports that 25 connections are available. Once started
        NetWorker checks the indexes for 22 clients.
        
        We have another NetWorker server with the same enabler codes but this
        one is not running!
        
        I've been trying to screw the problem but nothing worked (restarting
        NetWorker, restarting client, restarting server, deleting/recreating
        the client, etc.)
        
        Any help would be appreciated. Thank you in advance.
        
        
        Server: NetWorker 7.1.2.Build.325 Network Edition/25 - Red Hat
        Enterprise Linux 3.0
        Client: NetWorker 6.1.3.Build.428 - Solaris 8
        
        It worked fine with another server a few days ago. The only difference
        is the OS of the client, the successful backup was performed on a
        client running Debian.
        
        Best regards,
        David
        
        ________________________________________________________
        David De Maeyer
        Roskilde University Center, Department of Computer Science
        Box 260, Hus 42.1, 4000 Roskilde, Denmark
        voice (+45) 46 74 38 29 mobile (+45) 27 24 60 77 fax (+45) 46 74 30 72
        
        --
        Note: To sign off this list, send a "signoff networker" command via 
email
        to listserv AT listmail.temple DOT edu or visit the list's Web site at
        http://listmail.temple.edu/archives/networker.html where you can
        also view and post messages to the list.
        =*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=