Hello Gi Dot,

Could you try to run test command in btape tool and past here output
from this test?

The output text from the test command in btape can also advise adding
some directives to your Bacula config (BSF at EOM = yes/no ...and
others).

I have also question if you use "mt" or "mt-st" program to manage
magnetic tape drive? Your IBM DAT 160 works on SCSI bus (it is SAS)
and that is OK, because Bacula supports SCSI tape drives, of course. I
am asking about it because to tape drives on SCSI bus better is use
mt-st (magnetic tape control tool for SCSI tape driver) instead of mt
(standard magnetic tape control tool) to use proper ioctls for your
SCSI tape driver.

Thanks in advance for sending btape test output here.

Best regards.
Marcin Haba (gani)

On 5 September 2016 at 11:19, Gi Dot <gadidot AT gmail DOT com> wrote:
> Hi all,
>
> I am using IBM DAT 160 media with bacula, and I always get a tape error
> after a successful backup job. There were a lot of times that the tapes
> snapped as well. At first I thought the tapes are just defect, but the error
> occured so frequent that I started to doubt my bacula configuration.
>
> I used to get this error in the logs, but couldn't find similar error in
> recent logs:
>
> 05-May 15:54 hpsf-sd JobId 130: Volume "set1-w" previously written, moving
> to end of data.
> 05-May 15:54 hpsf-sd JobId 130: Error: Unable to position to end of data on
> device "ibm-dds6" (/dev/nst0): ERR=dev.c:776 ioct
> l MTEOM error on "ibm-dds6" (/dev/nst0). ERR=Input/output error.
>
> 05-May 15:54 hpsf-sd JobId 130: Marking Volume "set1-w" in Error in Catalog.
>
>
> Whenever this occured, I can only relabel the tape in order to reuse it. I
> hope anyone can have a look on the information of the tape settings and
> bacula configuration provided below, and advise if there is anything that is
> not right.
>
> # tapeinfo -f /dev/nst0
> Product Type: Tape Drive
> Vendor ID: 'IBM     '
> Product ID: 'DDS Gen6        '
> Revision: 'WU04'
> Attached Changer API: No
> SerialNumber: 'HU14086PJM'
> MinBlock: 1
> MaxBlock: 16777215
> SCSI ID: 0
> SCSI LUN: 0
> Ready: yes
> BufferedMode: yes
> Medium Type: Not Loaded
> Density Code: 0x48
> BlockSize: 0
> DataCompEnabled: yes
> DataCompCapable: yes
> DataDeCompEnabled: yes
> CompType: 0x20
> DeCompType: 0x0
> BOP: yes
> Block Position: 0
> Partition 0 Remaining Kbytes: 86814000
> Partition 0 Size in Kbytes: 86814000
> ActivePartition: 0
> EarlyWarningSize: 0
> NumPartitions: 0
> MaxPartitions: 1
>
>
> # mt -f /dev/nst0 status
> drive type = Generic SCSI-2 tape
> drive status = 1207959552
> sense key error = 0
> residue count = 0
> file number = 0
> block number = 0
> Tape block size 0 bytes. Density code 0x48 (DAT160).
> Soft error count since last status=0
> General status bits on (41010000):
>  BOT ONLINE IM_REP_E
>
>
> # bacula-sd.conf:
> Device {
>   Name = ibm-dds6
>   Media Type = DDS6
>   Device Type = tape
>   Archive Device = /dev/nst0
>   AlwaysOpen = yes;
>   Hardware End of Medium = no;
> # Two EOF = Yes
>   RemovableMedia = yes;
>   RandomAccess = no;
> }
>
>
> Before running the first job, mount script will be executed (run before
> job). After running the last job, umount script will be executed (run after
> job).
>
> # cat mount.sh
> #!/bin/sh
>
> /usr/sbin/bconsole -c /etc/bacula/bconsole.conf <<EOF
> mount storage=TapeDrive
> EOF
>
>
> # cat umount.sh
> #!/bin/sh
>
> /bin/sleep 60
>
> /usr/sbin/bconsole -c /etc/bacula/bconsole.conf <<EOF
> umount storage=TapeDrive
> EOF
>
> More from bacula.log:
> https://dpaste.de/uAYF/raw
>
>
>
>
>
> ------------------------------------------------------------------------------
>
> _______________________________________________
> Bacula-users mailing list
> Bacula-users AT lists.sourceforge DOT net
> https://lists.sourceforge.net/lists/listinfo/bacula-users
>



-- 
"Większej miłości nikt nie ma nad tę, jak gdy kto życie swoje kładzie
za przyjaciół swoich." Jezus Chrystus

------------------------------------------------------------------------------
_______________________________________________
Bacula-users mailing list
Bacula-users AT lists.sourceforge DOT net
https://lists.sourceforge.net/lists/listinfo/bacula-users