Re: [Bacula-users] Dell TL4000 labeling timeout

Hello Andrew,

I'm affraid your /dev/nst1 is your first drive (índex 0) and /dev/nst0 is your second drive (índex 1). From your mt status output, you have /dev/nst1 online with a tape loaded (i suspect this is the 44:000002L6 tape). Could you try changing this in your bacula-sd.conf (/dev/nst1 -> drive índex 0 and /dev/nst0 -> drive índex 1)?

Also, for your I/O slots being recognized by mtx-changer script, you need to do a modification inside de section for the "list" command:

if test ${vxa_packetloader} -ne 0 ; then

cat ${TMPFILE} | grep " *Storage Element [0-9]*:.*Full" | sed "s/ Storage Element //" | sed "s/Full :VolumeTag=//"

else

# cat ${TMPFILE} | grep " Storage Element [0-9]*:.*Full" | awk "{print \$3 \$4}" | sed "s/Full *$:VolumeTag=$*//"

cat ${TMPFILE} | sed "s/ IMPORT\/EXPORT//" | grep " Storage Element [0-9]*:.*Full" | awk "{print \$3 \$4}" | sed "s/Full *$:VolumeTag=$*//"

Best regards,

Ana

On Fri, Jun 19, 2015 at 12:34 AM, Andrew Noonan <anoonan AT gmail DOT com> wrote:

cat /proc/scsi/scsi:

Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: SEAGATE Model: ST373455SS Rev: S52C
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: SEAGATE Model: ST373455SS Rev: S52C
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi0 Channel: 01 Id: 00 Lun: 00
Vendor: Dell Model: VIRTUAL DISK Rev: 1028
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: DELL Model: MD32xx Rev: 0784
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 00 Lun: 01
Vendor: DELL Model: MD32xx Rev: 0784
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 00 Lun: 02
Vendor: DELL Model: MD32xx Rev: 0784
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 00 Lun: 03
Vendor: DELL Model: MD32xx Rev: 0784
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 00 Lun: 31
Vendor: DELL Model: Universal Xport Rev: 0784
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 01 Lun: 00
Vendor: DELL Model: MD32xx Rev: 0784
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 01 Lun: 01
Vendor: DELL Model: MD32xx Rev: 0784
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 01 Lun: 02
Vendor: DELL Model: MD32xx Rev: 0784
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 01 Lun: 03
Vendor: DELL Model: MD32xx Rev: 0784
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 01 Lun: 31
Vendor: DELL Model: Universal Xport Rev: 0784
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 00 Lun: 04
Vendor: DELL Model: MD32xx Rev: 0784
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 00 Lun: 05
Vendor: DELL Model: MD32xx Rev: 0784
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 01 Lun: 04
Vendor: DELL Model: MD32xx Rev: 0784
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 01 Lun: 05
Vendor: DELL Model: MD32xx Rev: 0784
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi2 Channel: 00 Id: 08 Lun: 00
Vendor: IBM Model: ULT3580-HH6 Rev: D8E5
Type: Sequential-Access ANSI SCSI revision: 06
Host: scsi2 Channel: 00 Id: 10 Lun: 00
Vendor: IBM Model: ULT3580-HH6 Rev: D8E5
Type: Sequential-Access ANSI SCSI revision: 06
Host: scsi2 Channel: 00 Id: 10 Lun: 01
Vendor: IBM Model: 3573-TL Rev: C.30
Type: Medium Changer ANSI SCSI revision: 05

sg_map -x

/dev/sg0 0 0 0 0 0
/dev/sg1 0 0 1 0 0
/dev/sg2 0 1 0 0 0 /dev/sda
/dev/sg3 1 0 0 0 0 /dev/sdb
/dev/sg4 1 0 0 1 0 /dev/sdc
/dev/sg5 1 0 0 2 0 /dev/sdd
/dev/sg6 1 0 0 3 0 /dev/sde
/dev/sg7 1 0 0 31 0 /dev/sdf
/dev/sg8 1 0 1 0 0 /dev/sdg
/dev/sg9 1 0 1 1 0 /dev/sdh
/dev/sg10 1 0 1 2 0 /dev/sdi
/dev/sg11 1 0 1 3 0 /dev/sdj
/dev/sg12 1 0 1 31 0 /dev/sdk
/dev/sg13 1 0 0 4 0 /dev/sdl
/dev/sg14 1 0 0 5 0 /dev/sdm
/dev/sg15 1 0 1 4 0 /dev/sdn
/dev/sg16 1 0 1 5 0 /dev/sdo
/dev/sg17 2 0 8 0 1 /dev/nst0
/dev/sg18 2 0 10 0 1 /dev/nst1
/dev/sg19 2 0 10 1 8

As an example of the status of things, here's the output of:

mtx-changer /dev/changer listall 0 /dev/nst0 0

D:0:F:44:000002L6
D:1:E
S:1:F:000045L6
S:2:F:000001L6
S:3:F:000046L6
S:4:F:000042L6
S:5:F:000043L6
S:6:F:000044L6
S:7:F:000038L6
S:8:F:000039L6
S:9:F:000040L6
S:10:F:000033L6
S:11:F:000034L6
S:12:F:000035L6
S:13:F:000036L6
S:14:F:000029L6
S:15:F:000030L6
S:16:F:000031L6
S:17:F:000032L6
S:18:F:000025L6
S:19:F:000026L6
S:20:F:000027L6
S:21:F:000028L6
S:22:F:000024L6
S:23:F:000023L6
S:24:F:000022L6
S:25:F:000021L6
S:26:F:000020L6
S:27:F:000019L6
S:28:F:000018L6
S:29:F:000017L6
S:30:F:000016L6
S:31:F:000015L6
S:32:F:000014L6
S:33:F:000013L6
S:34:F:000012L6
S:35:F:000011L6
S:36:F:000010L6
S:37:F:000009L6
S:38:F:000008L6
S:39:F:000007L6
S:40:F:000006L6
S:41:F:000005L6
S:42:F:000004L6
S:43:F:000003L6
S:44:E
I:45:F:000047L6
I:46:F:000041L6
I:47:F:000037L6

so you can see that drive 0 has the tape from slot 44 in it, and drive
1 is empty. 44 is the last slot that the "label barcode" seems to
know about... the "I" slots seem to be invisible to a normal "list"
command. So that was a tape loaded yesterday when I attempted to do a
"label barcode" with the 900 sec timeouts. I have not attempted to do
a load or unload for 24 hours. Here are the current mt status results
from these drives:

mt -f /dev/nst0 status
SCSI 2 tape drive:
File number=-1, block number=-1, partition=0.
Tape block size 0 bytes. Density code 0x0 (default).
Soft error count since last status=0
General status bits on (50000):
DR_OPEN IM_REP_EN

mt -f /dev/nst1 status
SCSI 2 tape drive:
File number=0, block number=0, partition=0.
Tape block size 0 bytes. Density code 0x5a (no translation).
Soft error count since last status=0
General status bits on (41010000):
BOT ONLINE IM_REP_EN

So after having the tape in the drive for more then 24 hours, the
state is still DR_OPEN on drive 0, which since the $ready variable is
ONLINE, will prevent mtx-changer from ever returning before it times
out.

On Thu, Jun 18, 2015 at 8:45 PM, Ana Emília M. Arruda

<emiliaarruda AT gmail DOT com> wrote:
> Hi Andrew,
>
> Also, can you send us "cat /proc/scsi/scis" and "sg_map -x"?
>
> Best regards,
> Ana
>
> On Thu, Jun 18, 2015 at 9:17 AM, Josh Fisher <jfisher AT pvct DOT com> wrote:
>>
>>
>>
>> On 6/17/2015 10:35 PM, Andrew Noonan wrote:
>> > @Marcin - dmesg is clean
>> >
>> > @Ana - I ~think~ /dev/changer is created by udev, I'm not 100%. It's
>> > a symlink to sg19 in this case:
>>
>> Most likely, udev got it right. Try mtx -f /dev/changer noattach status.
>> If that works, then try the load with the 'noattach' prefix. This drive
>> could be reporting it supports the _ATTACHED API, but does not exactly
>> comply/match with the expected API commands. The noattach prefix will
>> force mtx to use the regular media changer API.
>>
>>
>>
>> >
>> > lrwxrwxrwx 1 root root 4 Jun 10 17:06 /dev/changer -> sg19
>> > crw-rw---- 1 root disk 21, 19 Jun 10 17:06 /dev/sg19
>> >
>> > Here are the tape drive parts of "lsscsi -l". I removed a bunch of
>> > HDDs attached to the system:
>> >
>> > [2:0:8:0] tape IBM ULT3580-HH6 D8E5 /dev/st0
>> > state=running queue_depth=254 scsi_level=7 type=1 device_blocked=0
>> > timeout=900
>> > [2:0:10:0] tape IBM ULT3580-HH6 D8E5 /dev/st1
>> > state=running queue_depth=254 scsi_level=7 type=1 device_blocked=0
>> > timeout=900
>> > [2:0:10:1] mediumx IBM 3573-TL C.30 -
>> > state=running queue_depth=254 scsi_level=6 type=8 device_blocked=0
>> > timeout=0
>> >
>> > At some point we had the Tape unit powered down and then powered it
>> > back up, but the system remained on, so the dmesg mentions the drives
>> > multiple times:
>> >
>> > [anoonan@odin ~]$ dmesg | grep Attached
>> > sd 0:1:0:0: Attached scsi disk sda
>> > scsi 0:0:0:0: Attached scsi generic sg0 type 0
>> > scsi 0:0:1:0: Attached scsi generic sg1 type 0
>> > sd 0:1:0:0: Attached scsi generic sg2 type 0
>> > sd 1:0:0:0: Attached scsi disk sdb
>> > sd 1:0:0:0: Attached scsi generic sg3 type 0
>> > sd 1:0:0:1: Attached scsi disk sdc
>> > sd 1:0:0:1: Attached scsi generic sg4 type 0
>> > sd 1:0:0:2: Attached scsi disk sdd
>> > sd 1:0:0:2: Attached scsi generic sg5 type 0
>> > sd 1:0:0:3: Attached scsi disk sde
>> > sd 1:0:0:3: Attached scsi generic sg6 type 0
>> > sd 1:0:0:31: Attached scsi disk sdf
>> > sd 1:0:0:31: Attached scsi generic sg7 type 0
>> > sd 1:0:1:0: Attached scsi disk sdg
>> > sd 1:0:1:0: Attached scsi generic sg8 type 0
>> > sd 1:0:1:1: Attached scsi disk sdh
>> > sd 1:0:1:1: Attached scsi generic sg9 type 0
>> > sd 1:0:1:2: Attached scsi disk sdi
>> > sd 1:0:1:2: Attached scsi generic sg10 type 0
>> > sd 1:0:1:3: Attached scsi disk sdj
>> > sd 1:0:1:3: Attached scsi generic sg11 type 0
>> > sd 1:0:1:31: Attached scsi disk sdk
>> > sd 1:0:1:31: Attached scsi generic sg12 type 0
>> > scsi 2:0:0:0: Attached scsi generic sg13 type 1
>> > scsi 2:0:1:0: Attached scsi generic sg14 type 1
>> > st 2:0:0:0: Attached scsi tape st0
>> > st 2:0:1:0: Attached scsi tape st1
>> > st 2:0:2:0: Attached scsi tape st1
>> > st 2:0:2:0: Attached scsi generic sg14 type 1
>> > st 2:0:3:0: Attached scsi tape st1
>> > st 2:0:3:0: Attached scsi generic sg14 type 1
>> > st 2:0:4:0: Attached scsi tape st0
>> > st 2:0:4:0: Attached scsi generic sg13 type 1
>> > st 2:0:5:0: Attached scsi tape st1
>> > st 2:0:5:0: Attached scsi generic sg14 type 1
>> > scsi 2:0:5:1: Attached scsi generic sg15 type 8
>> > st 2:0:6:0: Attached scsi tape st0
>> > st 2:0:6:0: Attached scsi generic sg13 type 1
>> > scsi 2:0:6:1: Attached scsi generic sg14 type 8
>> > st 2:0:7:0: Attached scsi tape st1
>> > st 2:0:7:0: Attached scsi generic sg15 type 1
>> > sd 1:0:0:4: Attached scsi disk sdl
>> > sd 1:0:0:4: Attached scsi generic sg13 type 0
>> > sd 1:0:0:5: Attached scsi disk sdm
>> > sd 1:0:0:5: Attached scsi generic sg14 type 0
>> > sd 1:0:1:4: Attached scsi disk sdn
>> > sd 1:0:1:4: Attached scsi generic sg15 type 0
>> > sd 1:0:1:5: Attached scsi disk sdo
>> > sd 1:0:1:5: Attached scsi generic sg16 type 0
>> > st 2:0:8:0: Attached scsi tape st0
>> > st 2:0:8:0: Attached scsi generic sg17 type 1
>> > st 2:0:9:0: Attached scsi tape st1
>> > st 2:0:9:0: Attached scsi generic sg18 type 1
>> > scsi 2:0:9:1: Attached scsi generic sg19 type 8
>> > st 2:0:10:0: Attached scsi tape st1
>> > st 2:0:10:0: Attached scsi generic sg18 type 1
>> > scsi 2:0:10:1: Attached scsi generic sg19 type 8
>> >
>> > I did change out the device names for the drives to be /dev/tape/by-id
>> > names instead to make sure the naming stays stable after reboots, but
>> > I haven't tried changing /dev/changer to anything else. The btape
>> > tests were successful, and I haven't had any problems with mtx or even
>> > mt commands, though as mentioned previously, I've gotten Input/Output
>> > errors from mt when doing rewind/weof commands to the drives. That
>> > being said, I'm suspicious of the amount of time that mt reports
>> > DR_OPEN on loads. I can issue mtx-changer commands OK, as well,
>> > though I'm not sure if the "load" command is actually returning
>> > correctly, or is just timing out internally. unloads/list/listall
>> > from mtx-changer have always returned successfully.
>> >
>> > This is a Centos 5 machine, so not very new at all. mtx package is:
>> > mtx-1.2.18-9, mt-st is mt-st-0.9b-4.el5
>> >
>> > It may be a little challenge to upgrade this system (probably to
>> > Centos 6), but not impossible if it needs to happen.
>> >
>> > Thanks,
>> > Andrew
>> >
>> > On Wed, Jun 17, 2015 at 8:32 PM, Ana Emília M. Arruda
>> > <emiliaarruda AT gmail DOT com> wrote:
>> >> Hello Andrew,
>> >>
>> >> Is /dev/changer created by udev rules? Have you tried /dev/sgX instead?
>> >> Can
>> >> you send us the output of the "lsscsi -l" command and "dmesg | grep
>> >> Attached"? Have you checked your drives/autochanger using just mtx/mt
>> >> commands to see if they are working? Which is your mtx version?
>> >>
>> >> Best regards,
>> >> Ana
>> >>
>> >> On Wed, Jun 17, 2015 at 7:29 PM, Marcin Haba <ganiuszka AT gmail DOT com>
>> >> wrote:
>> >>> Hello,
>> >>>
>> >>> Do you have any errors in dmesg (hardware errors, bus reset, SCSI
>> >>> errors ... etc.) ?
>> >>>
>> >>> Best regards,
>> >>> Marcin Haba (gani)
>> >>>
>> >>> 2015-06-17 21:56 GMT+02:00 Andrew Noonan <anoonan AT gmail DOT com>:
>> >>>> Hi all,
>> >>>>
>> >>>> It's taking a lot longer because of the higher timeouts, but
>> >>>> the
>> >>>> label is still failing with a termination. If I understand it
>> >>>> correctly, the mtx-changer script is polling with 'mt' looking for
>> >>>> the
>> >>>> $ready state, defined in the config file as ONLINE (for Linux). I'm
>> >>>> not seeing drive 0 go into that state... I just see:
>> >>>>
>> >>>> SCSI 2 tape drive:
>> >>>> File number=-1, block number=-1, partition=0.
>> >>>> Tape block size 0 bytes. Density code 0x0 (default).
>> >>>> Soft error count since last status=0
>> >>>> General status bits on (50000):
>> >>>> DR_OPEN IM_REP_EN
>> >>>>
>> >>>> the other device looks like:
>> >>>>
>> >>>> SCSI 2 tape drive:
>> >>>> File number=0, block number=0, partition=0.
>> >>>> Tape block size 0 bytes. Density code 0x5a (no translation).
>> >>>> Soft error count since last status=0
>> >>>> General status bits on (41010000):
>> >>>> BOT ONLINE IM_REP_EN
>> >>>>
>> >>>> So I see that it's ~possible~ to see the ONLINE state, but it doesn't
>> >>>> seem like it ever gets to that state during load.
>> >>>>
>> >>>> Any thoughts?
>> >>>>
>> >>>> Thanks,
>> >>>> Andrew
>> >>>>
>> >>>> On Wed, Jun 17, 2015 at 11:44 AM, Andrew Noonan <anoonan AT gmail DOT com>
>> >>>> wrote:
>> >>>>> Hi Ana,
>> >>>>>
>> >>>>> Thanks for the reply. I'm adding those into the drives. BTW,
>> >>>>> 900 is the value. Having no real experience with these, is it
>> >>>>> abnormal for a load to take the 10+ minutes, or is that reasonable?
>> >>>>> My next step is to add those settings in, restart the SD, and
>> >>>>> attempt
>> >>>>> to do a "label barcode" again.
>> >>>>>
>> >>>>> Thanks,
>> >>>>> Andrew
>> >>>>>
>> >>>>> On Tue, Jun 16, 2015 at 9:10 PM, Ana Emília M. Arruda
>> >>>>> <emiliaarruda AT gmail DOT com> wrote:
>> >>>>>> Hello Andrew,
>> >>>>>>
>> >>>>>> You can find in the output of a "lsscsi -l" command the timeout for
>> >>>>>> your
>> >>>>>> drives. Then you can configure 3 timeout directives for each one of
>> >>>>>> your two
>> >>>>>> drives (LRADrive-1 e LRADrive-2):
>> >>>>>>
>> >>>>>> Maximum Changer Wait = X
>> >>>>>> Maximum Rewind Wait = X
>> >>>>>> Maximum Open Wait = X
>> >>>>>>
>> >>>>>> where X is the timeout value for your dirves.
>> >>>>>>
>> >>>>>> You can also customize your mtx-changer script for this timeout
>> >>>>>> changing the
>> >>>>>> bellow 300 seconds value:
>> >>>>>>
>> >>>>>> wait_for_drive() {
>> >>>>>> i=0
>> >>>>>> while [ $i -le 300 ]; do # Wait max 300 seconds
>> >>>>>>
>> >>>>>> Best regards,
>> >>>>>> Ana
>> >>>>>>
>> >>>>>>
>> >>>>>> On Tue, Jun 16, 2015 at 5:02 PM, Andrew Noonan <anoonan AT gmail DOT com>
>> >>>>>> wrote:
>> >>>>>>> Hi all,
>> >>>>>>>
>> >>>>>>> I'm almost completely new to tape. We've been doing disk-based
>> >>>>>>> backups for years, but we now have a project where we want to
>> >>>>>>> offsite
>> >>>>>>> hundreds of TB permanently, and have a Dell TL4000 (a rebranded
>> >>>>>>> IBM
>> >>>>>>> 3573-TL from the looks of it) with 2 ULT3580 LTO-6 drives. We're
>> >>>>>>> running bacula 5.2. The server is a Dell 1950 running Centos 5
>> >>>>>>> (sorry
>> >>>>>>> for the old OS).
>> >>>>>>>
>> >>>>>>> The btape tests run on both units without a problem, including the
>> >>>>>>> autochanger tests, and manually executing load/unload/list
>> >>>>>>> commands
>> >>>>>>> with mtx-changer seem to run fine. The one exception to this is
>> >>>>>>> that
>> >>>>>>> the mtx-changer load command seems to take about 10 minutes to
>> >>>>>>> complete, which seems unreasonably long. These are brand new
>> >>>>>>> tapes
>> >>>>>>> and I haven't written anything to them other then whatever btape
>> >>>>>>> does
>> >>>>>>> with testing. I put a 5 minute sleep on the load for mtx-changer,
>> >>>>>>> but
>> >>>>>>> other then that haven't customized the script, as I'm not sure
>> >>>>>>> what
>> >>>>>>> I'd customize.
>> >>>>>>>
>> >>>>>>> The "update slots" command from the director works OK, but when I
>> >>>>>>> go
>> >>>>>>> to do a "label barcode", the resulting "load slot" gets killed by
>> >>>>>>> Bacula:
>> >>>>>>>
>> >>>>>>> 3992 Bad autochanger "load slot 20, drive 1": ERR=Child died from
>> >>>>>>> signal 15: Termination.
>> >>>>>>> Results=Program killed by Bacula (timeout)
>> >>>>>>>
>> >>>>>>> I've seen that in some of these posts to the list, this ends up
>> >>>>>>> being
>> >>>>>>> permissions problems against the devices, but that doesn't seem to
>> >>>>>>> be
>> >>>>>>> the case as far as I can see:
>> >>>>>>>
>> >>>>>>> bacula-sd is running as the bacula user/group. The bacula user is
>> >>>>>>> in
>> >>>>>>> the "disk" group, and the *st* devices are in the disk group with
>> >>>>>>> "rw"
>> >>>>>>> permissions:
>> >>>>>>>
>> >>>>>>> crw-rw---- 1 root disk 9, 128 Jun 4 12:02 /dev/nst0
>> >>>>>>> crw-rw---- 1 root disk 9, 224 Jun 4 12:02 /dev/nst0a
>> >>>>>>> crw-rw---- 1 root disk 9, 160 Jun 4 12:02 /dev/nst0l
>> >>>>>>> crw-rw---- 1 root disk 9, 192 Jun 4 12:02 /dev/nst0m
>> >>>>>>> crw-rw---- 1 root disk 9, 129 Jun 10 17:06 /dev/nst1
>> >>>>>>> crw-rw---- 1 root disk 9, 225 Jun 10 17:06 /dev/nst1a
>> >>>>>>> crw-rw---- 1 root disk 9, 161 Jun 10 17:06 /dev/nst1l
>> >>>>>>> crw-rw---- 1 root disk 9, 193 Jun 10 17:06 /dev/nst1m
>> >>>>>>> crw-rw---- 1 root disk 9, 0 Jun 4 12:02 /dev/st0
>> >>>>>>> crw-rw---- 1 root disk 9, 96 Jun 4 12:02 /dev/st0a
>> >>>>>>> crw-rw---- 1 root disk 9, 32 Jun 4 12:02 /dev/st0l
>> >>>>>>> crw-rw---- 1 root disk 9, 64 Jun 4 12:02 /dev/st0m
>> >>>>>>> crw-rw---- 1 root disk 9, 1 Jun 10 17:06 /dev/st1
>> >>>>>>> crw-rw---- 1 root disk 9, 97 Jun 10 17:06 /dev/st1a
>> >>>>>>> crw-rw---- 1 root disk 9, 33 Jun 10 17:06 /dev/st1l
>> >>>>>>> crw-rw---- 1 root disk 9, 65 Jun 10 17:06 /dev/st1m
>> >>>>>>>
>> >>>>>>> Here's a block of debug from the SD during a label attempt for one
>> >>>>>>> of
>> >>>>>>> the
>> >>>>>>> slots:
>> >>>>>>>
>> >>>>>>> odin-sd: autochanger.c:434-0 Wiffle through devices looking for
>> >>>>>>> slot
>> >>>>>>> odin-sd: autochanger.c:313-0 Locking changer LogRepoAutochanger
>> >>>>>>> odin-sd: autochanger.c:740-0 omsg=/usr/lib64/bacula/mtx-changer
>> >>>>>>> /dev/changer loaded 14 /dev/nst0 0
>> >>>>>>> odin-sd: autochanger.c:272-0 Run
>> >>>>>>> program=/usr/lib64/bacula/mtx-changer
>> >>>>>>> /dev/changer loaded 14 /dev/nst0 0
>> >>>>>>> odin-sd: watchdog.c:206-0 Registered watchdog 636b888, interval
>> >>>>>>> 300
>> >>>>>>> odin-sd: bpipe.c:220-0 Wait for 28962 opt=1
>> >>>>>>> odin-sd: bpipe.c:228-0 Got break wpid=28962 status=0 ERR=none
>> >>>>>>> odin-sd: bpipe.c:249-0 child status=0
>> >>>>>>> odin-sd: watchdog.c:226-0 Unregistered watchdog 636b888
>> >>>>>>> odin-sd: bpipe.c:264-0 returning stat=0,0
>> >>>>>>> odin-sd: autochanger.c:274-0 run_prog:
>> >>>>>>> /usr/lib64/bacula/mtx-changer
>> >>>>>>> /dev/changer loaded 14 /dev/nst0 0 stat=0 result=0
>> >>>>>>> odin-sd: autochanger.c:327-0 Unlocking changer LogRepoAutochanger
>> >>>>>>> odin-sd: autochanger.c:313-0 Locking changer LogRepoAutochanger
>> >>>>>>> odin-sd: autochanger.c:740-0 omsg=/usr/lib64/bacula/mtx-changer
>> >>>>>>> /dev/changer loaded 14 /dev/nst1 1
>> >>>>>>> odin-sd: autochanger.c:272-0 Run
>> >>>>>>> program=/usr/lib64/bacula/mtx-changer
>> >>>>>>> /dev/changer loaded 14 /dev/nst1 1
>> >>>>>>> odin-sd: watchdog.c:206-0 Registered watchdog 636b888, interval
>> >>>>>>> 300
>> >>>>>>> odin-sd: bpipe.c:220-0 Wait for 28976 opt=1
>> >>>>>>> odin-sd: bpipe.c:228-0 Got break wpid=28976 status=0 ERR=none
>> >>>>>>> odin-sd: bpipe.c:249-0 child status=0
>> >>>>>>> odin-sd: watchdog.c:226-0 Unregistered watchdog 636b888
>> >>>>>>> odin-sd: bpipe.c:264-0 returning stat=0,0
>> >>>>>>> odin-sd: autochanger.c:274-0 run_prog:
>> >>>>>>> /usr/lib64/bacula/mtx-changer
>> >>>>>>> /dev/changer loaded 14 /dev/nst1 1 stat=0 result=0
>> >>>>>>> odin-sd: autochanger.c:327-0 Unlocking changer LogRepoAutochanger
>> >>>>>>> odin-sd: autochanger.c:453-0 Slot=14 not found in another device
>> >>>>>>> odin-sd: autochanger.c:313-0 Locking changer LogRepoAutochanger
>> >>>>>>> odin-sd: autochanger.c:183-0 Doing changer load slot 14
>> >>>>>>> "LRADrive-2"
>> >>>>>>> (/dev/nst1)
>> >>>>>>> odin-sd: autochanger.c:740-0 omsg=/usr/lib64/bacula/mtx-changer
>> >>>>>>> /dev/changer load 14 /dev/nst1 1
>> >>>>>>> odin-sd: dev.c:1746-0 close_dev "LRADrive-2" (/dev/nst1)
>> >>>>>>> odin-sd: dev.c:1751-0 device "LRADrive-2" (/dev/nst1) already
>> >>>>>>> closed
>> >>>>>>> vol=
>> >>>>>>> odin-sd: autochanger.c:190-0 Run
>> >>>>>>> program=/usr/lib64/bacula/mtx-changer
>> >>>>>>> /dev/changer load 14 /dev/nst1 1
>> >>>>>>> odin-sd: watchdog.c:206-0 Registered watchdog 636b888, interval
>> >>>>>>> 300
>> >>>>>>> odin-sd: bpipe.c:443-0 Run program fgets killed=1
>> >>>>>>> odin-sd: bpipe.c:220-0 Wait for 28990 opt=1
>> >>>>>>> odin-sd: bpipe.c:228-0 Got break wpid=28990 status=15 ERR=none
>> >>>>>>> odin-sd: bpipe.c:256-0 Child died from signal 15
>> >>>>>>> odin-sd: watchdog.c:235-0 Unregistered inactive watchdog 636b888
>> >>>>>>> odin-sd: bpipe.c:264-0 returning stat=15,134217743
>> >>>>>>> odin-sd: autochanger.c:205-0 load slot 14, drive 1, bad
>> >>>>>>> stats=Child
>> >>>>>>> died from signal 15: Termination.
>> >>>>>>> odin-sd: autochanger.c:212-0 load slot 14 status=134217743
>> >>>>>>> odin-sd: autochanger.c:327-0 Unlocking changer LogRepoAutochanger
>> >>>>>>> odin-sd: autochanger.c:218-0 After changer, status=134217743
>> >>>>>>> odin-sd: dev.c:1735-0 Clear volhdr vol=
>> >>>>>>> odin-sd: vol_mgr.c:544-0 vol_unused: no vol on "LRADrive-2"
>> >>>>>>> (/dev/nst1)
>> >>>>>>> odin-sd: lock.c:302-0 return lock. old=BST_WRITING_LABEL from
>> >>>>>>> dircmd.c:554
>> >>>>>>> odin-sd: lock.c:307-0 return lock. new=BST_NOT_BLOCKED
>> >>>>>>> odin-sd: dev.c:1746-0 close_dev "LRADrive-2" (/dev/nst1)
>> >>>>>>> odin-sd: dev.c:1751-0 device "LRADrive-2" (/dev/nst1) already
>> >>>>>>> closed
>> >>>>>>> vol=
>> >>>>>>> odin-sd: acquire.c:731-0 Enter detach_dcr_from_dev
>> >>>>>>> odin-sd: dircmd.c:220-0 <dird: label LogRepoAutochanger
>> >>>>>>> VolumeName=000030L6 PoolName=LogrepoArchive MediaType=LTO-6
>> >>>>>>> Slot=15
>> >>>>>>> drive=1
>> >>>>>>> odin-sd: dircmd.c:234-0 Do command: label
>> >>>>>>> odin-sd: dircmd.c:627-0 Try changer device LRADrive-1
>> >>>>>>> odin-sd: dircmd.c:648-0 Device LogRepoAutochanger drive wrong:
>> >>>>>>> want=1
>> >>>>>>> got=0 skipping
>> >>>>>>> odin-sd: dircmd.c:627-0 Try changer device LRADrive-2
>> >>>>>>> odin-sd: dircmd.c:643-0 Found changer device LRADrive-2
>> >>>>>>> odin-sd: dircmd.c:656-0 Found device LRADrive-2
>> >>>>>>> odin-sd: block.c:144-0 Returning new block=636b800
>> >>>>>>> odin-sd: acquire.c:713-0 JobId=0 enter attach_dcr_to_dev
>> >>>>>>> odin-sd: dircmd.c:421-0 Can label. Device is not open
>> >>>>>>> odin-sd: lock.c:285-0 steal lock. old=BST_NOT_BLOCKED from
>> >>>>>>> dircmd.c:470
>> >>>>>>> odin-sd: lock.c:290-0 steal lock. new=BST_WRITING_LABEL
>> >>>>>>> odin-sd: dircmd.c:471-0 Stole device "LRADrive-2" (/dev/nst1)
>> >>>>>>> lock,
>> >>>>>>> writing label.
>> >>>>>>>
>> >>>>>>> The config I've got for these is:
>> >>>>>>>
>> >>>>>>> Device {
>> >>>>>>> Name = LRADrive-1
>> >>>>>>> Alert Command = "sh -c 'smartctl -H -l error %c'"
>> >>>>>>> AlwaysOpen = yes
>> >>>>>>> ArchiveDevice = /dev/nst0
>> >>>>>>> AutoChanger = yes
>> >>>>>>> AutomaticMount = yes
>> >>>>>>> DeviceType = Tape
>> >>>>>>> DriveIndex = 0
>> >>>>>>> LabelMedia = no
>> >>>>>>> MediaType = LTO-6
>> >>>>>>> RandomAccess = no
>> >>>>>>> RemovableMedia = yes
>> >>>>>>> }
>> >>>>>>>
>> >>>>>>> Device {
>> >>>>>>> Name = LRADrive-2
>> >>>>>>> Alert Command = "sh -c 'smartctl -H -l error %c'"
>> >>>>>>> AlwaysOpen = yes
>> >>>>>>> ArchiveDevice = /dev/nst1
>> >>>>>>> AutoChanger = yes
>> >>>>>>> AutomaticMount = yes
>> >>>>>>> DeviceType = Tape
>> >>>>>>> DriveIndex = 1
>> >>>>>>> LabelMedia = no
>> >>>>>>> MediaType = LTO-6
>> >>>>>>> RandomAccess = no
>> >>>>>>> RemovableMedia = yes
>> >>>>>>> }
>> >>>>>>>
>> >>>>>>> Autochanger {
>> >>>>>>> Name = LogRepoAutochanger
>> >>>>>>> ChangerCommand = "/usr/lib64/bacula/mtx-changer %c %o %S %a %d"
>> >>>>>>> ChangerDevice = /dev/changer
>> >>>>>>> Device = LRADrive-1
>> >>>>>>> Device = LRADrive-2
>> >>>>>>> }
>> >>>>>>>
>> >>>>>>>
>> >>>>>>> I know there are some things that could be optimized here for
>> >>>>>>> performance, and I'm certainly interested in them, but right now I
>> >>>>>>> can't even label my tapes :)
>> >>>>>>>
>> >>>>>>> I suspect it's the long load delay, and I wasn't sure if maybe the
>> >>>>>>> drive is searching for some mark or something. On that note, I
>> >>>>>>> tried
>> >>>>>>> to do a "rewind" and "weof" using the /dev/st0 device (wasn't sure
>> >>>>>>> if
>> >>>>>>> nst0 would complain about issuing a rewind), but I would get
>> >>>>>>> "Input/Output error" messages from mt on both the rewind and weof
>> >>>>>>> commands.
>> >>>>>>>
>> >>>>>>> Any advice I could get would be helpful.
>> >>>>>>>
>> >>>>>>> Thanks!
>> >>>>>>> Andrew
>> >>>>>>>
>> >>>>>>>
>> >>>>>>>
>> >>>>>>>
>> >>>>>>> ------------------------------------------------------------------------------
>> >>>>>>> _______________________________________________
>> >>>>>>> Bacula-users mailing list
>> >>>>>>> Bacula-users AT lists.sourceforge DOT net
>> >>>>>>> https://lists.sourceforge.net/lists/listinfo/bacula-users
>> >>>>>>
>> >>>>
>> >>>>
>> >>>> ------------------------------------------------------------------------------
>> >>>> _______________________________________________
>> >>>> Bacula-users mailing list
>> >>>> Bacula-users AT lists.sourceforge DOT net
>> >>>> https://lists.sourceforge.net/lists/listinfo/bacula-users
>> >>>
>> >>>
>> >>> --
>> >>> "Większej miłości nikt nie ma nad tę, jak gdy kto życie swoje kładzie
>> >>> za przyjaciół swoich." Jezus Chrystus
>> >>>
>> >>>
>> >>>
>> >>> ------------------------------------------------------------------------------
>> >>> _______________________________________________
>> >>> Bacula-users mailing list
>> >>> Bacula-users AT lists.sourceforge DOT net
>> >>> https://lists.sourceforge.net/lists/listinfo/bacula-users
>> >>
>> >
>> > ------------------------------------------------------------------------------
>> > _______________________________________________
>> > Bacula-users mailing list
>> > Bacula-users AT lists.sourceforge DOT net
>> > https://lists.sourceforge.net/lists/listinfo/bacula-users
>>
>>
>>
>> ------------------------------------------------------------------------------
>> _______________________________________________
>> Bacula-users mailing list
>> Bacula-users AT lists.sourceforge DOT net
>> https://lists.sourceforge.net/lists/listinfo/bacula-users
>
>
>
> ------------------------------------------------------------------------------
>
> _______________________________________________
> Bacula-users mailing list
> Bacula-users AT lists.sourceforge DOT net
> https://lists.sourceforge.net/lists/listinfo/bacula-users
>

------------------------------------------------------------------------------
_______________________________________________
Bacula-users mailing list
Bacula-users AT lists.sourceforge DOT net
https://lists.sourceforge.net/lists/listinfo/bacula-users

------------------------------------------------------------------------------

_______________________________________________
Bacula-users mailing list
Bacula-users AT lists.sourceforge DOT net
https://lists.sourceforge.net/lists/listinfo/bacula-users