Hello Jean-François,

I seem to be having problems with the SCSI controller:

st0: Error 80000 (sugg. bt 0x0, driver bt 0x0, host bt 0x8).

scsi(0:0:6:0): Queueing device reset command.

Bye.


Luc Lalonde wrote:

Hello Jean-François,

I think I found the problem. I have another old binary 'mt' in the PATH that is causing the problem. After removing I get the same output as you do:

[root@abel ~]# mt -f /dev/nst0 status
SCSI 2 tape drive:
File number=0, block number=0, partition=0.
Tape block size 512 bytes. Density code 0x0 (default).
Soft error count since last status=0
General status bits on (41010000):
BOT ONLINE IM_REP_EN
[root@abel bin]# /bin/mt -f /dev/nst1 status
SCSI 2 tape drive:
File number=0, block number=0, partition=0.
Tape block size 512 bytes. Density code 0x0 (default).
Soft error count since last status=0
General status bits on (41010000):
BOT ONLINE IM_REP_EN

When I do an amcheck I get this error (changerdev "/dev/sg0"):

scsi(0): Resetting Cmnd=0x000001000b06b880, Handle=0x0000000000000202, action=0x2

scsi(0:0:6:0): Queueing device reset command.

So the changer seems to be struggling...

I'm  continuing my investigations...
Thanks again for your input...

Luc Lalonde wrote:

Hello Jean-François,

I'm getting this weird message with 'mt':

[root@abel ~]# mt -f /dev/nst0 status
Unknown tape drive type (0x72):
  residual= 0   ds = 200   er = 0
  file no= 0   block no= 0

What I don't understand is that it seems to be correctly recognized by the system:

[root@abel ~]# cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 06 Lun: 00
 Vendor: STK      Model: L40              Rev: 0215
 Type:   Medium Changer                   ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 15 Lun: 00
 Vendor: SEAGATE  Model: ULTRIUM06242-XXX Rev: 1619
 Type:   Sequential-Access                ANSI SCSI revision: 03
Host: scsi0 Channel: 01 Id: 15 Lun: 00
 Vendor: SEAGATE  Model: ULTRIUM06242-XXX Rev: 1619
 Type:   Sequential-Access                ANSI SCSI revision: 03

Any ideas? By the way, the jukebox is connected to the server via a Qlogic QLA1240. What are you using on your Linux box?

Thanks again.

PS: 'mtx -f /dev/sg0 status' seems to work fine. I get a full report of the contents of my library.

Jean-Francois Malouin wrote:

* Luc Lalonde <Luc.Lalonde AT polymtl DOT ca> [20060811 11:52]:

Hello Folks,

I'm getting this error when I try to use the tapes (LTO1) on a StorageTek L40 Jukebox:

st1: Block limits 1 - 16777215 bytes.
st1: Incorrect block size.
st1: Incorrect block size.

scsi(0): Resetting Cmnd=0x000001004a871b00, Handle=0x0000000000000202, action=0x2

scsi(0:1:15:0): Queueing device reset command.
st1: Error with sense data: Current st1: sense key Not Ready
Additional sense: Logical unit not ready, cause not reportable

I'm in the process of migrating Amanda from a SGI (Origin 300) server to a Linux server. I'm hoping that I don't have to re-label all my tapes and lose the backups created with the old SGI Amanda server.

I'm in the middle of relocating our entire computer room so I'll be
brief :) I have a bunch of LTO1s in a L80 hooked to a O3k so that's
essentially what you have. I'll be moving this to a Debian system soon
and in my testings I could drive the library and tape drives with mtx
and mt no problem except for the hardware compression bit on the
drive: after much mucking around with stinit I couldn't disable it but
seems the for LTO that's not a problem. Still looking for a way to
disable it though.

To your problem: what does 'mt status' says?

Here's what I got on a Debian system running 2.6.x

~# mt -f /dev/nst0 status
SCSI 2 tape drive:
File number=0, block number=0, partition=0.
Tape block size 512 bytes. Density code 0x0 (default).
Soft error count since last status=0
General status bits on (41010000):
 BOT ONLINE IM_REP_EN

~# ./amtapetype -o -f /dev/nst0 -e 100g
Writing 1024 Mbyte   compresseable data:  35 sec
Writing 1024 Mbyte uncompresseable data:  69 sec
WARNING: Tape drive has hardware compression enabled
Estimated time to write 2 * 102400 Mbyte: 13800 sec = 3 h 50 min
wrote 3178496 32Kb blocks in 97 files in 6880 seconds (short write)
wrote 3194880 32Kb blocks in 195 files in 6886 seconds (short write)
define tapetype unknown-tapetype {
    comment "just produced by tapetype prog (hardware compression on)"
    length 99584 mbytes
    filemark 0 kbytes
    speed 14815 kps
}

HTH
jf

Thanks!

--
Luc Lalonde, analyste
---------------------------------------------------------------------
Département de génie informatique:
Éole polytechnique de Montréal
(514) 340-4711 x5049
Luc.Lalonde AT polymtl DOT ca
---------------------------------------------------------------------