I figured this one out, the file system that I was trying to use
crashed, and was mounted read-only.  Sorry about crying wolf....

Scott

On Wed, Jul 09, 2003 at 07:09:20PM -0700, Scott Petler wrote:
> 
> Amanda was working fine, but now I get the following from amcheck:
> Not sure what happened, any ideas.  I'll also put other relevant files
> after.  I don't remember changing anything.
> 
> Thanks
> 
> 
> Amanda Tape Server Host Check
> -----------------------------
> amcheck-server: slot 12: chg-multi: slot is empty
> amcheck-server: slot 13: chg-multi: slot is empty
> amcheck-server: slot 14: chg-multi: slot is empty
> amcheck-server: slot 1: chg-multi: slot is empty
> amcheck-server: slot 2: chg-multi: slot is empty
> amcheck-server: slot 3: chg-multi: slot is empty
> amcheck-server: slot 4: chg-multi: slot is empty
> amcheck-server: slot 5: chg-multi: slot is empty
> amcheck-server: slot 6: chg-multi: slot is empty
> amcheck-server: slot 7: chg-multi: slot is empty
> amcheck-server: slot 8: chg-multi: slot is empty
> amcheck-server: slot 9: chg-multi: slot is empty
> amcheck-server: slot 10: chg-multi: slot is empty
> amcheck-server: slot 11: chg-multi: slot is empty
> ERROR: label DailySet105 or new tape not found in rack
>        (expecting tape DailySet105 or a new tape)
> NOTE: skipping tape-writable test
> Server check took 5.256 seconds
> 
> Amanda Backup Client Hosts Check
> --------------------------------
> Client check: 1 host checked in 0.173 seconds, 0 problems found
> 
> (brought to you by Amanda 2.4.4)
> 
> **************
> tapelist
> **************
> 20030708 DailySet104 reuse
> 20030707 DailySet103 reuse
> 20030706 DailySet102 reuse
> 20030704 DailySet101 reuse
> 0 DailySet114 reuse
> 0 DailySet113 reuse
> 0 DailySet112 reuse
> 0 DailySet111 reuse
> 0 DailySet110 reuse
> 0 DailySet109 reuse
> 0 DailySet108 reuse
> 0 DailySet107 reuse
> 0 DailySet106 reuse
> 0 DailySet105 reuse
> 
> **************
> changer.conf
> **************
> 
> multieject 0
> gravity 0
> needeject 0
> ejectdelay 0
> 
> statefile /var/lib/amanda/DailySet1/changer-status
> 
> firstslot 1
> lastslot 14
> 
> slot 1 file:/backup/amandadumps/tape01
> slot 2 file:/backup/amandadumps/tape02
> slot 3 file:/backup/amandadumps/tape03
> slot 4 file:/backup/amandadumps/tape04
> slot 5 file:/backup/amandadumps/tape05
> slot 6 file:/backup/amandadumps/tape06
> slot 7 file:/backup/amandadumps/tape07
> slot 8 file:/backup/amandadumps/tape08
> slot 9 file:/backup/amandadumps/tape09
> slot 10 file:/backup/amandadumps/tape10
> slot 11 file:/backup/amandadumps/tape11
> slot 12 file:/backup/amandadumps/tape12
> slot 13 file:/backup/amandadumps/tape13
> slot 14 file:/backup/amandadumps/tape14
> 
> **************
> amanda.conf
> **************
> 
> org "DailySet1"         # your organization name for reports
> mailto "root"           # space separated list of operators at your site
> dumpuser "backup"       # the user to run dumps under
> inparallel 4            # maximum dumpers that will run in parallel (max 63)
> dumporder "sssS"        # specify the priority order of each dumper
> netusage  6000 Kbps     # maximum net bandwidth for Amanda, in KB per sec
> dumpcycle 10 days       # the number of days in the normal dump cycle
> tapecycle 14 tapes      # the number of tapes in rotation
> bumpsize 20 Mb          # minimum savings (threshold) to bump level 1 -> 2
> bumpdays 1              # minimum days at each level
> bumpmult 4              # threshold = bumpsize * bumpmult^(level-1)
> etimeout 300            # number of 
> dtimeout 1800           # number of idle seconds before a dump is aborted.
> ctimeout 30             # maximum number of seconds that amcheck waits
> tapebufs 20
> runtapes 1              # number of tapes to be used in a single run of amdump
> tpchanger "chg-multi"   # t
> changerfile "/usr/local/etc/amanda/DailySet1/changer.conf"
> maxdumpsize 40 gbytes  
> tapetype HARD-DISK              # what kind of tape it is (see tapetypes 
> below)
> labelstr "^DailySet1[0-9][0-9]*$" # label constraint regex: all tapes must 
> match
> amrecover_do_fsf yes            # amrecover will call amrestore with the
> amrecover_check_label yes       # amrecover will call amrestore with the
> amrecover_changer "/dev/null"   # amrecover will use the changer if you 
> restore
> autoflush no #
> define tapetype HARD-DISK {
>         comment "use disk instead of tape"
>         length 40 gbytes
> }
> define dumptype hard-disk-dump {
>         global
>         holdingdisk no
>         priority high
> }
> 
> define dumptype hard-disk-tar {
>         hard-disk-dump
>         comment "Backup to to hard disk instead of tape - using tar"
>         program "GNUTAR"
> }
> 
> define dumptype hard-disk-tar-nocomp {
>         hard-disk-dump
>         compress none
>         comment "Backup to to hard disk instead of tape - using tar"
>         program "GNUTAR"
> }
> 
>