I am getting a problem were I have added a media server with shared storage
and when I try to do a backup of that server using it's storage device, I
get an error code 98. Anyone got any ideas. It will backup over the
network fine, but when I try to do a SSO backup with that particular media
server, it fails.
Thanks in advance,
Rick Keahey
-----Original Message-----
From: W. Curtis Preston [mailto:curtis AT colltech DOT com]
Sent: Thursday, June 29, 2000 11:26 AM
To: Martin, Barbara; Pascal VIOLERO AI/DI-TA;
veritas-bu AT mailman.eng.auburn DOT edu
Subject: RE: [Veritas-bu] How to add or remove a slave server without
stop ping master and all others slaves
My biggest problem that I've found is when one creates a new storage
unit. I have never been able to add a new storage unit and get backups to
go that storage unit without a stop/start. Otherwise, you just get a
"storage unit unavailable" message. How do you get around that problem?
At 12:03 PM 6/29/00 -0400, Martin, Barbara wrote:
>I am surprised to learn that Veritas does not officially support adding or
>removing a slave with the master and all other slaves active. I have done
>this several times. Once with a Veritas consultant on site. As long as
>there are no current backups running on the slave to be removed and you
have
>no backups scheduled to go to that slave, there are no problems with
>removing the slave. The same for adding a slave, which is even easier
since
>you cannot configure backups to the new slave until after the slave is
>active. I have never had to stop all backups on the master and other
>slaves. I have the adding of a new slave procedure documented. Please
>contact me if you want further information.
>
>Barb Martin
>Voice: (937)445-3674
>VoicePlus: 622-3674
>FAX: (937)445-3398
>mailto:barbara.martin AT DaytonOH.NCR DOT COM
>
>
>
> > -----Original Message-----
> > From: Pascal VIOLERO AI/DI-TA [SMTP:pascal.violero AT airbus DOT fr]
> > Sent: Thursday, June 29, 2000 3:34 AM
> > To: veritas-bu AT mailman.eng.auburn DOT edu
> > Subject: [Veritas-bu] How to add or remove a slave server without
> > stopping master and all others slaves
> >
> >
> >
> >
> >
> >
> >
> > Hi,
> >
> > Veritas indicate to us that it's mandatory to stop all slave
> > servers and master to add a new slave
> > server in the configuration, so all backups are stopped.
> >
> > Do you know if a solution exist (as is not supported by
> > veritas) to add or remove a slave without stopping master
> > and
> > others slaves, and if it's possible without stopping current
> > backup.
> >
> > Best regards,
> >
> > --------------------------------------
> > Pascal Violero (AI/DI-T)
> > Phone : 05.61.9(3.28.03)
> > Email : pascal.violero AT airbus DOT fr
> > Fax : 05.61.9(3.35.67)
> > --------------------------------------
> > _______________________________________________
> > Veritas-bu maillist - Veritas-bu AT mailman.eng.auburn DOT edu
> > http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu
>_______________________________________________
>Veritas-bu maillist - Veritas-bu AT mailman.eng.auburn DOT edu
>http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu
---
W. Curtis Preston, Principal Consultant at Collective Technologies
Email: curtis AT colltech DOT com (Best way to contact me)
Work : 408 452 5555 (Leave a message.)
Pager: 800 946 4646, pin#1436065 (If urgent.)
Tap into the Collective Intellect (TM): http://www.colltech.com
Backup & Restore resources: http://www.backupcentral.com
_______________________________________________
Veritas-bu maillist - Veritas-bu AT mailman.eng.auburn DOT edu
http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu
|