Hello,
I think you need to check if your drives is in the correct order with
Command "sjisn btl" or put a cartridge in one drive and verify with "mt"
command the tape contains the cartridge
Kind Regards
_____________________________________
Jean-Pierre GIROT
Technical Support Department
LCNA
MTI France
7 Avenue des Pommerots - BP 25 -
78401 Chatou Cedex
Tel: +33 130095349
Fax: +33 130095333
Email: jgirot AT fr.mti DOT com
______________________________________
-----Message d'origine-----
De : Evan Gold [mailto:egold AT FSA DOT COM]
Envoyé : mercredi 4 février 2004 20:57
À : NETWORKER AT LISTMAIL.TEMPLE DOT EDU
Objet : [Networker] legato 7.1.1 and HP ultrium2 fiber drives upgrade problem
Hi All,
I run legato 7.1.1 on windows2000 server
i used to run with HP LTO-1 scsi tape drives
i just replaced them with HP-LTO2 fiber drives
windows sees the drives fine, and i installed the latest drivers for them.
i see them fine as LTO2-SCSI when i run "inquire", but they are fiber
drives, i dont know if thats the issue.
i deleted my old jukebox and tape drives and readded them with jbconfig as
"LTO2" drives. i then rebooted the server.
my jukebox is still full of LTO1 tapes
i rebooted and tried to run an inventory and also tried to mount a tape
with legato admin.
It loads the LTO1 tape into the drive but then legato keeps saying "unload
retry, sleeping for 30 seconds" forever when i run the inventory and/or
mount a tape.
If i open the jukebox i can load and unload the tapes fine using the tape
drives buttons.
any ideas what my issue is?
i keep getting these messages:
NetWorker media: (warning) \\.\Tape3 reading: read open error: drive status
is There is not a tape in the drive
here is output of my inquire command:
C:\Documents and Settings\Administrator>inquire
[email protected]:TEAC CD-224E 9.9A|CD-ROM
[email protected]:STK L180 0306|Autochanger (Jukebox),
\\.\Changer0
S/N: MPC02209470
[email protected]:COMPAQ SCSI COMMUNICATECISS|Unknown Device Type
[email protected]:COMPAQ LOGICAL VOLUME 2.56|Disk, \\.\PHYSICALDRIVE0
WWNN:600508B1001841385850494356340002
[email protected]:COMPAQ LOGICAL VOLUME 2.56|Disk, \\.\PHYSICALDRIVE1
WWNN:600508B1001841385850494356340003
[email protected]:HP Ultrium 2-SCSI K342|Tape, \\.\Tape0
S/N: HUM3G00050
ATNN:HP Ultrium 2-SCSI
HUM3G000
50
WWNN:50060B00001E6372
[email protected]:HP Ultrium 2-SCSI K342|Tape, \\.\Tape1
S/N: HUM3G00246
ATNN:HP Ultrium 2-SCSI
HUM3G002
46
WWNN:50060B00001E6682
[email protected]:HP Ultrium 2-SCSI K342|Tape, \\.\Tape2
S/N: HUM3G00040
ATNN:HP Ultrium 2-SCSI
HUM3G000
40
WWNN:50060B00001E634A
[email protected]:Emulex Utility Ifc Dev.EMU2|(Unknown Device Type b)
[email protected]:HP Ultrium 2-SCSI K342|Tape, \\.\Tape3
S/N: HUM3G00349
ATNN:HP Ultrium 2-SCSI
HUM3G003
49
WWNN:50060B00001E681E
[email protected]:HP Ultrium 2-SCSI K342|Tape, \\.\Tape4
S/N: HUM3G00046
ATNN:HP Ultrium 2-SCSI
HUM3G000
46
WWNN:50060B00001E6362
[email protected]:HP Ultrium 2-SCSI K342|Tape, \\.\Tape5
S/N: HUM3G00255
ATNN:HP Ultrium 2-SCSI
HUM3G002
55
WWNN:50060B00001E66A6
[email protected]:Emulex Utility Ifc Dev.EMU2|(Unknown Device Type b)
C:\Documents and Settings\Administrator>
C:\Documents and Settings\Administrator>nsrjb -Iv
setting verbosity level to `1'
nsrjb: Looking at device `\\.\Tape0' id 0.
nsrjb: Looking at device `\\.\Tape1' id 1.
nsrjb: Looking at device `\\.\Tape2' id 2.
nsrjb: Looking at device `\\.\Tape3' id 3.
nsrjb: Looking at device `\\.\Tape4' id 4.
nsrjb: Looking at device `\\.\Tape5' id 5.
device = \\.\Tape0, id = 0, reserved = 1, busy = 0, mode = 0
device = \\.\Tape1, id = 1, reserved = 1, busy = 0, mode = 0
device = \\.\Tape2, id = 2, reserved = 1, busy = 0, mode = 0
device = \\.\Tape3, id = 3, reserved = 1, busy = 0, mode = 0
device = \\.\Tape4, id = 4, reserved = 1, busy = 0, mode = 0
device = \\.\Tape5, id = 5, reserved = 1, busy = 0, mode = 0
Jukebox handle being opened at port [email protected]
box_inventory:
nsrjb: About to read label on \\.\Tape0
nsrjb: About to read label on \\.\Tape3
Jukebox handle being closed at port [email protected]
box_inventory_free:
nsrjb: About to eject volume from \\.\Tape0
nsrjb: About to eject volume from \\.\Tape3
\\.\Tape0: verified label of -. (not in the media index)
\\.\Tape3: verified label of -. (not in the media index)
eject sleep for 5 seconds
eject sleep for 5 seconds
Jukebox handle being opened at port [email protected]
Slot `117' is being loaded into drive `\\.\Tape1'
box_display: `' for drive `\\.\Tape1'
Jukebox handle being closed at port [email protected]
load sleep for 5 seconds
Jukebox handle being opened at port [email protected]
Unloading jukebox: drive `\\.\Tape0' into slot `1'
box_unload: unload failure detected - retrying
box_unload: retry: start time = 1075924354
box_unload: retry: sleeping 30
box_unload: retry: failed - will retry
box_unload: retry: sleeping 30
box_unload: retry: failed - will retry
box_unload: retry: sleeping 30
C:\Documents and Settings\Administrator>
thank you very much!
Evan
--
Note: To sign off this list, send a "signoff networker" command via email
to listserv AT listmail.temple DOT edu or visit the list's Web site at
http://listmail.temple.edu/archives/networker.html where you can
also view and post messages to the list.
=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=
--
Note: To sign off this list, send a "signoff networker" command via email
to listserv AT listmail.temple DOT edu or visit the list's Web site at
http://listmail.temple.edu/archives/networker.html where you can
also view and post messages to the list.
=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=
|
