[nv-l] Problems loading Extreme net MIBs and some other as well

Hi all,

I am a newbie to Netview world, so, please, do not hesitate to correct
me. I have a lot of problems loading MIBs, most of which are down to
some problems in the MIBs themselves. Some, however, are not. I have
used a way recomended on this list to tell if the file is v2 or v1. So
far I have not been able to load any of the v2 files, and you can se the
output bellow:


bash-2.05b# xnmloadmib2 -load
/usr/mibs/standards/TOKEN-RING-RMON-MIB.txt -replace
Warning: This entry has no sub-identifier(entityXMIB): On or around line
185827 of the snmpv2mib file.
Warning: The mib description doesn't seem to be consistent.
 Some nodes couldn't be linked under the "iso" tree.
 These nodes are left:
Left-over node rptrInfoResetEvent ::= {  5 } (0)
Left-over node rptrInfoHealth ::= {  4 } (0)
Left-over node rptrResetEvent ::= {  3 } (0)
Left-over node rptrGroupChange ::= {  2 } (0)
Left-over node rptrHealth ::= {  1 } (0)
Left-over node dot1xSuppMaxStart ::= { dot1xSuppConfigEntry 5 } (1)
Left-over node dot1xSuppStartPeriod ::= { dot1xSuppConfigEntry 4 } (1)
Left-over node dot1xSuppAuthPeriod ::= { dot1xSuppConfigEntry 3 }
(1).................

I have these leftover nodes more than 1000... I have tried to load all
v2 CISCO mibs.... I have tried also all the standard v2 mibs...


If you say that I have to start over, I will do that gladly...

On the other hand, below is another one, for Extreme networks. I can not
see any problems with the file. I have tried with the official one (from
Extreme net) and the one from ByteSphere's
http://www.oidview.com/mibs/detail.html


bash-2.05b# xnmloadmib2 -load /usr/mibs/Enterprises/Extreme\ Networks\
Inc/ExtremeWare\ -\ Extreme\ 7.2.0\ MIB/extreme_m1.mib -replace
Warning: This entry has no sub-identifier(entityXMIB): On or around line
185827 of the snmpv2mib file.
Error detected while loading MIB File: /usr/mibs/Enterprises/Extreme
Networks Inc/ExtremeWare - Extreme 7.2.0 MIB/extreme_m1.mib.
This MIB cannot be loaded until the following problem is corrected:

Bad format of optional clauses(}): On or around line 6532
Bad parse of OBJECT-TYPE: On or around line 6532
Mib table is bad.


Since, I will, probably have to start changing mibs, do you have any
tools (freeware if possible, we have bought Tivoli Netview and TEC :))
which could help me, or some links where I could find the exact
definition for a MIB file (no RFCs please, I have tried, trust me, I do
not have the time for that.

I hope that I am not too picky.

In the end: We are running NetView 7.1.4 on AIX 5.2L 

bash-2.05b$ uname -a
AIX tivoli 2 5 005D6ACC4C00

Thank you all for your patience with this e-mail.

Have a nice day.

Kind Regards,

Vladan Milosevic
Senior Engineer
IP Network and Services
Information Technology Division
063 MOBTEL Srbija
 
tel.    +381 11 30 13 106
fax     +381 11 30 13 452
GSM     +381 63 230 973
e-mail: vladan.milosevic AT mobtel.co DOT yu