Hi Frank, All,
 
I wanted to ask how you 'turn on' and 'turn off' the holding area?  
 
Also - I'm unable to click/drag/move objects on my map to containers I want 
them to be in. . .does anyone know if there's a configuration change I need to 
invoke that allows me to do that?
 
Thanks to all in advance. . .
 
Dan
 
 

        -----Original Message----- 
        From: DePhillips, Frank [mailto:fdephillips AT McLeodUSA DOT com] 
        Sent: Fri 3/28/2003 12:43 PM 
        To: 'James Shanks'; nv-l AT lists.tivoli DOT com 
        Cc: 
        Subject: RE: [nv-l] problem with node not showing up on map
        
        

        James, 

                I have the holding area turned on so all new routers get placed 
in the holding area before I put them on the map.  I added four routers last 
week and this one did not show up.  I did a locate and the router was not found 
by name or ip address.  I just ran the ovobjprint command and looked for the ip 
address and name in the output and it was not found. I have one map that is 
running production monitoring and I'm currently running a new map to clean up 
placement of nodes.

                I just tried to create the router by adding a new object and it 
comes back with the object selection name already exists and is a different 
type.

                Any other way I can find this object and delete it? 

        Thanks 

        Frank 

        -----Original Message----- 
        From: James Shanks [mailto:jshanks AT us.ibm DOT com] 
        Sent: Friday, March 28, 2003 8:48 AM 
        To: nv-l AT lists.tivoli DOT com 
        Subject: Re: [nv-l] problem with node not showing up on map 


        How do you know it's not on the map?  Did you try Locate? 
        If Locate fails to find it, then print the database with ovobjprint, 
        "ovobjprint > ovobjprint.out", and examine the output.    If you find 
the 
        object it should have two fields, OVW Maps Exit and OVW Maps Managed 
and 
        they should both have at least  a value of 1.  Do they?   At the bottom 
of 
        the record will be entries for the IP Symbol List for each of your 
maps. 
        You should have at least one map, usually called "default", so you 
should 
        see at least one entry which says "default IP Symbol List" followed by 
        some number.   Is that there?  Do you have more than one map? 

        James Shanks 
        Level 3 Support  for Tivoli NetView for UNIX and NT 
        Tivoli Software / IBM Software Group 




        "DePhillips, Frank" <fdephillips AT McLeodUSA DOT com> 
        03/28/2003 09:38 AM 

        
                To:     nv-l AT lists.tivoli DOT com 
                cc: 
                Subject:        [nv-l] problem with node not showing up on map 





                I have added a node to the seedfile and run netmon -y and it 
does not show 
        up on the map.  If I try to create the node manually it will say node 
        already exsists.  How can I find this node or delete and recreate? 
        Thanks 
        Frank 




        NOTICE: This electronic mail transmission may contain confidential 
        information and is intended only for the person(s) named.  Any use, 
        copying or disclosure by any other person is strictly prohibited. If 
you 
        have received this transmission in error, please notify the sender via 
        e-mail. 





        --------------------------------------------------------------------- 
        To unsubscribe, e-mail: nv-l-unsubscribe AT lists.tivoli DOT com 
        For additional commands, e-mail: nv-l-help AT lists.tivoli DOT com 

        *NOTE* 
        This is not an Offical Tivoli Support forum. If you need immediate 
        assistance from Tivoli please call the IBM Tivoli Software Group 
        help line at 1-800-TIVOLI8(848-6548) 



        NOTICE: This electronic mail transmission may contain confidential 
information and is intended only for the person(s) named.  Any use, copying or 
disclosure by any other person is strictly prohibited. If you have received 
this transmission in error, please notify the sender via e-mail.