nv-l

Re: tecad_nv6k starts with EIF error

2001-12-21 16:59:52
Subject: Re: tecad_nv6k starts with EIF error
From: Eliza Chi <elizachi728 AT yahoo DOT com>
To: nv-l AT lists.tivoli DOT com
Date: Fri, 21 Dec 2001 13:59:52 -0800 (PST)
James,

I could not find Netview 6.0.3 release notes on Tivoli
web site.  I saw 6.0, 6.0.1, 6.0.2 and then 7.1.

Does Tivoli still have a 6.0.3 CDs for NT?

Thanks
Mei
--- James Shanks <jshanks AT us.ibm DOT com> wrote:
> I would call Support and get the latest tecad binary
> from them there were 
> problems with the EIF library build in 6.0, 6.0.1,
> and 6.0.2, which are 
> not corrected until 6.0.3.  The APAR is PJ28060.  I
> would not even attempt 
> to proceed without this fix.  And I would make plans
> to get 6.0.3 itself.
> 
> James Shanks
> Level 3 Support  for Tivoli NetView for UNIX and NT
> Tivoli Software / IBM Software Group
>  
> 
> 
> 
> 
> 
> Eliza Chi <elizachi728 AT yahoo DOT com>
> Sent by: owner-nv-l AT tkg DOT com
> 12/21/2001 03:00 PM
> Please respond to IBM NetView Discussion
> 
>  
>         To:     nv-l AT tkg DOT com
>         cc: 
>         Subject:        [NV-L] tecad_nv6k starts
> with EIF error
> 
>  
> 
> Hi,
> 
> Can someone help me to figure out the problem? 
> Thanks
> in advance.
> 
> ---------------------------
> My environment:
> 
> Spoke TMR server 3.6.2, (NT)/Netview Server 6.0.1
> (NT)
> TEC Netview adapter 3.6 are on one machine which is
> my
> Netview server.
> 
> Hub TMR 3.6.2 (NT)
> 
> TEC 3.6.2 (NT) in hub TMR.
> -----------------------------
> I have been tring to send netview events to the TEC
> server in the hub TMR, but the behavior attribute of
> "ovstatus tecad_nv6k" always shows:
> started... then not running. 
> I looked at log file from the tecio module
> configured
> in tecad_nv6k.err and saw the following error
> message.
>  
> 
> Fri Dec 21 14:14:03 2001   FATAL: TECIO  , err 01,
> ibtecad/tec_io.c line 0516: C
> annot create EIF handle. Please check the .conf
> file. 
> 
> I know this message is related to the ServerLocation
> in tecad_nv6k.conf, but I configured the
> ServerLocation:
> 
>      [email protected]#hub_tmr-region
> 
> I even tried @EventServer, Server IP, Server
> hostname
> but to the same error message. (I knew these did not
> make sense to me, but I just tried)
> 
> I have done:
> 
> 1. wlsconn on both hub tmr and spoke tmr/Netview 
> I saw two way interconnected tmrs
> 
> 2. odadmin odlist on both tmr and they are fine
> 
> 3. wupdate -r EventServer hub_tmr-region on the 
> spoke tmr/netview server, 
> 
> 4. wlookup -ar EventServer
> shows the EventServer with the hub tmr region oid
> 
> 5. wpostemsg OV_IF_Down events works fine from a
> CLI,
> tec processed the OV_IF_Down messages, the events
> were
> displayed on TEC Console
> 
> but I still can't bring up tecad_nv6k. Did I miss
> anything? 
> 
> I installed TEC on the spoke tmr/Netview server
> once,
> but I did wdel /Library/EventServer and wregister -u
> -r
> EventServer EventServer, wchkdb, so the spoke
> tmr/netview now only sees the tec server in hub tmr
> and wpostemsg works fine.
> 
> Did anyone get this error before.  Does any one know
> what ibtecad/tec_io.c line 0516 is trying to check? 
> 
> 
> 
> Eli
>  
> 
> 
> 
> __________________________________________________
> Do You Yahoo!?
> Check out Yahoo! Shopping and Yahoo! Auctions for
> all of
> your unique holiday gifts! Buy at
> http://shopping.yahoo.com
> or bid at http://auctions.yahoo.com
>
_________________________________________________________________________
> NV-L List information and Archives:
> http://www.tkg.com/nv-l
> 
> 
> 


__________________________________________________
Do You Yahoo!?