nv-l

Re: sysName

2001-10-31 10:12:22
Subject: Re: sysName
From: "CATALINA MARTINEZ" <CATALINA.MARTINEZ AT tlc.state.tx DOT us>
To: nv-l AT lists.tivoli DOT com
Date: Wed, 31 Oct 2001 09:12:22 -0600
This is a MIME message. If you are reading this text, you may want to 
consider changing to a mail reader or gateway that understands how to 
properly handle MIME multipart messages.
Thank you, I will try this (keeping my fingers crossed).

>>> shochste AT us.ibm DOT com 10/31/01 08:56AM >>>
Catalina,

The only "clean" way to do this that I can think of:

Assumption:   You are not managing over 5000 nodes (or this may cause
performance issue)

1. Configure your AIX box to use /etc/hosts first, then DNS.
2. Write a script that goes through all the nodes that NetView knows about,
does and snmpget of sysname and stores the data in /etc/hosts
     (create a collection of just "nodes", then use nvutil to list the
members of that collection to process)
3. After storing the data about the node, it does a demandpoll of the node.
At that time NetView should recognize the new hostname and update the
selection name

I have not tested this, but I think it would be worth a try.

Thanks,
Stephen Hochstetler            shochste AT us.ibm DOT com
ITSO Tivoli Coordinator - Austin
Office - 512-436-8564       FAX - 512-436-1991

ITSO redbooks at  http://www.redbooks.ibm.com


                                                                                
                                                                 
                    "CATALINA MARTINEZ"                                         
                                                                 
                    <CATALINA.MARTINEZ AT tlc DOT st       To:     <nv-l AT tkg 
DOT com>                                                                       
                    ate.tx.us>                      cc:                         
                                                                 
                    Sent by:                        Subject:     [NV-L] sysName 
                                                                 
                    owner-nv-l AT tkg DOT com                                   
                                                                        
                                                                                
                                                                 
                                                                                
                                                                 
                    10/31/2001 08:24 AM                                         
                                                                 
                    Please respond to IBM                                       
                                                                 
                    NetView Discussion                                          
                                                                 
                                                                                
                                                                 
                                                                                
                                                                 



Hi All,

Is it possible to get netview to pull the sysName and use it as the
Selection Name on cisco devices and servers(AIX, NT, 2000)?

CiscoWorks can do this and I have been asked to get Netview to do the same.
(from my previous emails, we are trying to get away from the host file)

Any suggestions?

Catalina Martinez
AIX 4.3.3.7
Framework 3.7.1
Netview 6.0.2


_________________________________________________________________________
NV-L List information and Archives: http://www.tkg.com/nv-l
Thank you, I will try this (keeping my fingers crossed).

>>> shochste AT us.ibm DOT com 10/31/01 08:56AM >>>
Catalina,

The only "clean" way to do this that I can think of:

Assumption:   You are not managing over 5000 nodes (or this may cause
performance issue)

1. Configure your AIX box to use /etc/hosts first, then DNS.
2. Write a script that goes through all the nodes that NetView knows about,
does and snmpget of sysname and stores the data in /etc/hosts
     (create a collection of just "nodes", then use nvutil to list the
members of that collection to process)
3. After storing the data about the node, it does a demandpoll of the node.
At that time NetView should recognize the new hostname and update the
selection name

I have not tested this, but I think it would be worth a try.

Thanks,
Stephen Hochstetler            shochste AT us.ibm DOT com
ITSO Tivoli Coordinator - Austin
Office - 512-436-8564       FAX - 512-436-1991

ITSO redbooks at  http://www.redbooks.ibm.com


                                                                                                                                                
                    "CATALINA MARTINEZ"                                                                                                         
                    <CATALINA.MARTINEZ AT tlc DOT st       To:     <nv-l AT tkg DOT com>                                                                      
                    ate.tx.us>                      cc:                                                                                         
                    Sent by:                        Subject:     [NV-L] sysName                                                                 
                    owner-nv-l AT tkg DOT com                                                                                                          
                                                                                                                                                
                                                                                                                                                
                    10/31/2001 08:24 AM                                                                                                         
                    Please respond to IBM                                                                                                       
                    NetView Discussion                                                                                                          
                                                                                                                                                
                                                                                                                                                



Hi All,

Is it possible to get netview to pull the sysName and use it as the
Selection Name on cisco devices and servers(AIX, NT, 2000)?

CiscoWorks can do this and I have been asked to get Netview to do the same.
(from my previous emails, we are trying to get away from the host file)

Any suggestions?

Catalina Martinez
AIX 4.3.3.7
Framework 3.7.1
Netview 6.0.2


_________________________________________________________________________
NV-L List information and Archives: http://www.tkg.com/nv-l




<Prev in Thread] Current Thread [Next in Thread>
  • sysName, CATALINA MARTINEZ
    • Re: sysName, Stephen Hochstetler
    • Re: sysName, CATALINA MARTINEZ <=