Have you rebooted the box since you changed the setting? Changing it alone
won't take the port away from someone who already has it.
Since these are not normal problems, perhaps you could tell us how you got into
this situation. Just following the install directions in the release notes
won't get you here.
James Shanks
Tivoli (NetView for UNIX) L3 Support
"Frank W. Hansen" <fhansen AT ENTERPRISEINNOVATIONS DOT COM> on 09/28/99
07:20:06 AM
Please respond to Discussion of IBM NetView and POLYCENTER Manager on NetView
<NV-L AT UCSBVM.UCSB DOT EDU>
To: NV-L AT UCSBVM.UCSB DOT EDU
cc: (bcc: James Shanks/Tivoli Systems)
Subject: Re: NT version 5.1 question
Xu,
I went ahead and disabled "SNMP Trap Service" and I do not have any other
application that would be using this port, any other thoughts?
Thanks
----- Original Message -----
From: Xu He <xuhe AT YAHOO DOT COM>
To: <NV-L AT UCSBVM.UCSB DOT EDU>
Sent: Tuesday, September 28, 1999 9:33 AM
Subject: Re: NT version 5.1 question
> Frank,
>
> Port 162 is used for SNMP Traps. There's another
> application acting as the trap receiver on your box.
> It could be the NT default trap daemon, or Bay
> Optivity, Openview, Spectrum, etc. You can look under
> \winnt\system32\drivers\etc\services, to find out
> where exactly is it mapping to. I don't know too much
> about where to disable Optivity, but for NT, go to
> services, under SNMP Trap Service, the default option
> should be disabled.
>
> Hope this works
> Xu He
>
> --- "Frank W. Hansen"
> <fhansen AT ENTERPRISEINNOVATIONS DOT COM> wrote:
> > Thank you Xu, that corrected one problem but on to
> > another one. Now trapd
> > is complaining stating that another process has port
> > 162. I have checked
> > the services listening on 162. No trap or other
> > process is using that port.
> > Any hints?
> >
> > Thanks!
> >
> > ----- Original Message -----
> > From: Xu He <xuhe AT YAHOO DOT COM>
> > To: <NV-L AT UCSBVM.UCSB DOT EDU>
> > Sent: Tuesday, September 28, 1999 8:22 AM
> > Subject: Re: NT version 5.1 question
> >
> >
> > > The NetView service is initial run under the
> > NetView
> > > userid in NT. The ID is normally assigned
> > Administer
> > > privilage and/or Log On As Service privilege. Did
> > you
> > > change the password for the NetView ID? if you
> > did,
> > > you have to change it under Control Panel ->
> > Services
> > > -> Netview.
> > >
> > > If someone happens to delete the NetView ID,
> > either
> > > recreated using usrmgr, or launch the service
> > using
> > > another ID with the correct privilege.
> > >
> > > Hope this helps.
> > > Xu He
> > >
> > >
> > > --- "Frank W. Hansen"
> > > <fhansen AT ENTERPRISEINNOVATIONS DOT COM> wrote:
> > > > Nothing else in the NetView log but in the NT
> > System
> > > > Log, I receive the following:
> > > >
> > > > "The NetView Service service failed to start due
> > to
> > > > the following error:
> > > > The service did not start due to a logon
> > failure."
> > > >
> > > > Best Regards,
> > > >
> > > > Frank W. Hansen
> > > > Tivoli Enterprise Certified Consultant
> > > >
> > > > Enterprise Innovations
> > > > www.enterpriseinnovations.com
> > > > 910 458 9172
> > > >
> > > > ----- Original Message -----
> > > > From: Vladimir Petr
> > > > To: NV-L AT UCSBVM.UCSB DOT EDU
> > > > Sent: Tuesday, September 28, 1999 4:52 AM
> > > > Subject: Re: NT version 5.1 question
> > > >
> > > >
> > > > Hi, Frank;
> > > > Is there more detailed information in the
> > NetView
> > > > Log (accessible from the NetView Start Menu
> > group)?
> > > > Could be of some help.
> > > > Best regards,
> > > > Vladimir.
> > > >
> > > > "Frank W. Hansen" wrote:
> > > >
> > > > Greetings. I am unable to start my NetView
> > > > daemons on NT. When I issue the command
> > "ovstart
> > > > -v" I receive the following error: Error
> > starting
> > > > NetView service, error=1069OVsPMD not running.
> > Best
> > > > Regards, Frank W. Hansen
> > > > Tivoli Enterprise Certified Consultant
> > > > Enterprise Innovations
> > > > www.enterpriseinnovations.com
> > > > 910 458 9172
> > > >
> > >
> > >
> > > =====
> > > Xu He
> > > Consulting Services Engineer
> > > Network Solutions, Inc
> > > http://www.netsol.com/consulting
> > > __________________________________________________
> > > Do You Yahoo!?
> > > Bid and sell for free at http://auctions.yahoo.com
> >
>
>
> =====
> Xu He
> Consulting Services Engineer
> Network Solutions, Inc
> http://www.netsol.com/consulting
> __________________________________________________
> Do You Yahoo!?
> Bid and sell for free at http://auctions.yahoo.com
|
