Re: [Veritas-bu] robot not enabled.
2008-07-14 16:02:39
thanks dave. yes the os does see the library as
well as the drive.
SunOS truxtun 5.10 Generic_127127-11 sun4u sparc
SUNW,Sun-Fire-V210 bash-3.00# /usr/openv/volmgr/bin/sgscan /dev/sg/c0t0l0:
Disk (/dev/rdsk/c1t0d0): "FUJITSU MAW3073NCSUN72G" /dev/sg/c0t1l0: Disk
(/dev/rdsk/c1t1d0): "FUJITSU MAW3073NCSUN72G" /dev/sg/c1t0l0: Changer:
"EXABYTE LTO 1x7 2U" /dev/sg/c1t3l0: Tape (/dev/rmt/0):
"HP Ultrium 3-SCSI"
bash-3.00#
/usr/openv/volmgr/bin/scan ************************************************************ ***********************
SDT_TAPE ************************ ***********************
SDT_CHANGER ************************ *********************** SDT_OPTICAL
************************ ************************************************************ ------------------------------------------------------------ Device
Name : "/dev/sg/c1t0l0" Passthru Name: "/dev/sg/c1t0l0" Volume
Header: "" Port: -1; Bus: -1; Target: -1; LUN:
-1 Inquiry : "EXABYTE LTO 1x7
2U B00B" Vendor ID : "EXABYTE
" Product ID : "LTO 1x7 2U " Product Rev:
"B00B" Serial Number:
"000087005544" WWN :
"" WWN Id Type : 0 Device Identifier: "EXABYTE LTO 1x7
2U 000087005544" Device Type
: SDT_CHANGER NetBackup Robot Type:
8 Removable : Yes Device Supports:
SCSI-4 Number of Drives : 1 Number of Slots : 7 Number of Media
Access Ports: 0 Drive 1 Serial Number :
"D217H001HU" Flags : 0x0 Reason:
0x0 ------------------------------------------------------------ Device
Name : "/dev/rmt/0cbn" Passthru Name: "/dev/sg/c1t3l0" Volume
Header: "" Port: -1; Bus: -1; Target: -1; LUN:
-1 Inquiry : "HP Ultrium
3-SCSI D217" Vendor ID : "HP
" Product ID : "Ultrium 3-SCSI " Product Rev: "D217" Serial
Number:
"HU171200RB" WWN :
"" WWN Id Type : 0 Device Identifier: "" Device
Type : SDT_TAPE NetBackup Drive Type:
16 Removable : Yes Device Supports:
SCSI-3 Flags : 0x0 Reason: 0x0
bash-3.00# /usr/openv/volmgr/bin/tpconfig
-l Device Robot
Drive
Robot
Drive
Device
Second Type
Num
Index Type
DrNum Status
Comment
Name
Path
Device Path robot
0
-
TLD
-
-
- -
/dev/sg/c1t0l0 drive
-
0
hcart3
-
UP - HP.ULTRIUM3-SCSI.000
/dev/rmt/0cbn
Does the OS see the
robot? Check that using sgscan -- if the OS doesn’t see the changer then
that’s your problem.
From:
veritas-bu-bounces AT mailman.eng.auburn DOT edu
[mailto:veritas-bu-bounces AT mailman.eng.auburn DOT edu] On Behalf Of Taylor, David
(MARSYS) Sent: Monday, July 14,
2008 12:19 To:
veritas-bu AT mailman.eng.auburn DOT edu Subject: [Veritas-bu] robot not
enabled.
good
morning. i am setting up a test disaster recovery server running netbackup 6
mp5 on a v210 with solaris 10 with a exabyte magnum 1x7
autoloader. running the storage device wizard fails thus leaving the robot
disabled "not enabled", the lto 3 tape drive is picked up without
problems. i have tried to configure the robot manually using tpconfig but get
the some results.
any ideas?
thanks,
dave..
|
_______________________________________________
Veritas-bu maillist - Veritas-bu AT mailman.eng.auburn DOT edu
http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu
|
|
|