unsure of your see your deviceses in cfgparameters...might work fine,
but I ususally do a "cfgadm -al -o show_FCP_dev" which will show if the
FC devices are visable.
You'd want to see
"c#::WWN,LUN#         tape         connected    configured   unknown"
for every tape device, plus an entry for the robot.
 
if you don't have a response from cfgadm for every device, every
sg.build/install and boot -r in the world won't help you.
 
That tell's you your zoning/physical layer stuff is good adn the devices
are responding properly.
then do your sg.build, making sure you have a high enough mt and ml for
the number of devices you have, then the sg.install, then do a sgscan to
see if NBU sees the devices....if you're goo at that point, delete
everything in /dev/rmt, and do the reconfigure reboot.
 
Paul
 
-- 

        -----Original Message-----
        From: veritas-bu-bounces at mailman.eng.auburn.edu
[mailto:veritas-bu-bounces at mailman.eng.auburn.edu] On Behalf Of
Sponsler, Michael
        Sent: April 25, 2007 4:19 PM
        To: veritas-bu at mailman.eng.auburn.edu
        Subject: [Veritas-bu] Cannot configure fibre san on Sun V880
        
        

        Master Server: Sol 10 on Sun v440, Netbackup 6.0 MP4 connected
to PX506 via fibre San 
        Media Server: Sol 8 on Sun v880, Netbackup 6.0 MP4 connected to
(same) PX506 via fibre San. 

        I cannot get my Sol 8 Sun v880 netbackup media server to create
the /dev/rmt device nodes.  The /devices..../st* files do not exist
either.

        I ran through the sg.build on everything.  Doing an sgscan on
the Sol 8 media server: 

        /dev/sg/c0tw100000e002233aafl0: Changer: "Quantum PX500" 
        /dev/sg/c0tw100000e002233aafl1: Tape (???): "Qauntum SDLT600" 
        /dev/sg/c0tw100000e002233aafl2: Tape (???): "Qauntum SDLT600" 

        No /dev/rmt devices exist for my PX506 drives. 

        I do have a stand alone SDLT600 "shoebox" connected via scisi
local on the v880 that does have /dev/rmt/0* devices. 

        When doing a "devfsadm -vc tape" 
        I get "invalid st_rdev" 

        A reconfiguration reboot doesn't do anything either. 

        The PX506 fibre setup works with my Sol 10 master server, and
various other Sol 8 Media Servers. 

        I'm using a QLA 2310 fibre card, and yes it has the Sun F-Code
on it. 

        Any ideas? 

        -- 
        Mike Sponsler 
        Northrop Grumman 
        Michael.Sponsler at ngc.com 

====================================================================================

La version fran?aise suit le texte anglais.

------------------------------------------------------------------------------------

This email may contain privileged and/or confidential information, and the Bank 
of
Canada does not waive any related rights. Any distribution, use, or copying of 
this
email or the information it contains by other than the intended recipient is
unauthorized. If you received this email in error please delete it immediately 
from
your system and notify the sender promptly by email that you have done so. 

------------------------------------------------------------------------------------

Le pr?sent courriel peut contenir de l'information privil?gi?e ou 
confidentielle.
La Banque du Canada ne renonce pas aux droits qui s'y rapportent. Toute 
diffusion,
utilisation ou copie de ce courriel ou des renseignements qu'il contient par une
personne autre que le ou les destinataires d?sign?s est interdite. Si vous 
recevez
ce courriel par erreur, veuillez le supprimer imm?diatement et envoyer sans 
d?lai ?
l'exp?diteur un message ?lectronique pour l'aviser que vous avez ?limin? de 
votre
ordinateur toute copie du courriel re?u.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: 
http://mailman.eng.auburn.edu/pipermail/veritas-bu/attachments/20070425/25d3fe1f/attachment-0001.htm