Turned out fine.
I had to turn on the Extended virtual SAN option (or something to that
effect).
Once I had that on, I could see the devices of the library as LUNs and
the hosts visible via the SAN (master and filer)
And control which LUNs on the library were visible to each host.
Seems fine now.
Found the NDMP software on the "add ons" disk....just looking for MP3
now.....wonder why Veritas (symantec) dropped so much from their FTP
site.
Thanks.
Paul
> -----Original Message-----
> From: veritas-bu-admin AT mailman.eng.auburn DOT edu
> [mailto:veritas-bu-admin AT mailman.eng.auburn DOT edu] On Behalf Of
> william.d.brown AT gsk DOT com
> Sent: October 7, 2005 6:15 AM
> To: Veritas List
> Subject: RE: [Veritas-bu] partitioning a ADIC Scalar 24 w/FC
>
>
> Hmm, I don't immediately see why adding a zone with the
> NetApp is spoiling
> it.
>
>
> <<So configured as above, the NB server should see only robot
> and a single
> drive, and the filer should see just one drive?
> >>
>
> That's right. Make sure you don't present the library
> 'partition' i.e. the
> robot control to the NetApp, just the drive.
>
> It is possible there is a problem, I've heard of other
> occasions where a
> NetApp could not be in the same zone - but should be OK in an
> overlapping
> zone like this. I'm basing my advice on a Scalar i2000 and the AMC
> manual. My Scalar 24 is on order....
>
> Worst case you could try the other way round, control the
> robot over NDMP
> from the NetApp, give the other server just a drive.....
>
>
> William D L Brown
>
>
>
>
> "Paul Keating" <pkeating AT bank-banque-canada DOT ca>
> Sent by: veritas-bu-admin AT mailman.eng.auburn DOT edu
> 06-Oct-2005 14:38
>
> To
> william.d.brown AT gsk DOT com, "Veritas List"
> <veritas-bu AT mailman.eng.auburn DOT edu>
> cc
>
> Subject
> RE: [Veritas-bu] partitioning a ADIC Scalar 24 w/FC
>
>
>
>
>
>
>
>
> > -----Original Message-----
> > From: veritas-bu-admin AT mailman.eng.auburn DOT edu
> > [mailto:veritas-bu-admin AT mailman.eng.auburn DOT edu] On Behalf Of
> > william.d.brown AT gsk DOT com
> > Sent: October 6, 2005 4:45 AM
> > To: Veritas List
> > Subject: Re: [Veritas-bu] partitioning a ADIC Scalar 24 w/FC
> >
> >
> > You need a SAN switch. You connect both the filer and the
> > server to the
> > switch, and zone both to the fibre connection for the Scalar 24.
>
> Check.
>
> >
> > Use separate zones - always have only one initiator in any SAN zone.
>
> Check.
>
> >
> > So now both the filer and the server can 'see' the fibre
> > router embedded
> > in the library.
>
> Working on this....an sgscan from the NB server will "see" the drives
> and robot, but end up only coming "up" in AVR control, unless there is
> only one zone......(NB server and library)...adding a second zone with
> Filer and Library seems to "pooch" things.
>
> >
> > Now you use the AMC software in the router, to configure the
> > presentation
> > of the SCSI devices on the fibre channel. You should find
> > that you can
> > select the host initiator (the router should by now have been
> > logged into
> > by the initiators). The AMC software then lets you choose
> from the
> > available SCSI-side resources - you will see the 'partition'
> > aka the robot
> > control - and the drives. You choose what FC LUN you want
> > them mapped to.
> > You should also see the control LUN, always LUN 0.
> >
> > So you can say set the robot as LUN 1 and one drive as LUN
> 2 for the
> > server. The other drive you can set also as LUN 1, but to
> > the filer.
>
> That's the way I want it....Master with robot and one drive,
> filer with
> the other drive.
>
> > Then on those systems rescan for devices, and you should see
> > them - then
> > you go on to configure the devices in the OS-dependant way.
>
> So configured as above, the NB server should see only robot
> and a single
> drive, and the filer should see just one drive?
>
> > Read the
> > Veritas PDFs on specific platform support for NDMP, as well
> > as the main
> > NDMP document - it covers what you need for the filer.
> >
> > Oh, and you need a tape FC HBA in the filer - different part
> > number to the
> > standard disk FC cards.
>
> Check.
>
>
> Thanks!!
>
> Paul
>
> _______________________________________________
> Veritas-bu maillist - Veritas-bu AT mailman.eng.auburn DOT edu
> http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu
>
>
>
>
> _______________________________________________
> Veritas-bu maillist - Veritas-bu AT mailman.eng.auburn DOT edu
> http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu
>
|
