First, if you have two SCSI drives per SCSI-FC bridge (e.g. a
Crossroads), then one drive will show up a LUN 0 and the other should show
up as LUN 1. Each bridge should be showing up as a separate SCSI target
on the same controller. This means that the first thing you'll need to
edit is the /kernel/drv/st.conf file. To start with, the 'st.conf' file
will need lines in it like the following (assuming the bridges are getting
SCSI targets 1-5 [I'm reserving 0 for other purposes]):
name="st" class="scsi" target=1 lun=0;
name="st" class="scsi" target=1 lun=1;
name="st" class="scsi" target=2 lun=0;
name="st" class="scsi" target=2 lun=1;
name="st" class="scsi" target=3 lun=0;
name="st" class="scsi" target=3 lun=1;
name="st" class="scsi" target=4 lun=0;
name="st" class="scsi" target=4 lun=1;
name="st" class="scsi" target=5 lun=0;
name="st" class="scsi" target=5 lun=1;
The exact lines will need to match the SCSI targets being assigned to the
bridges on your system. You'll need similar lines in the 'sg.conf' file
to see the drives in an 'sgscan'. Review the Media Manager Device
Configuration Guide (or is it the install guide?) on how to configure the
SG driver. You'll need to specify a value of at least 1 to the '-ml'
(max LUN) parameter to the 'sg.build' command. You also need to pay
careful attention to what SCSI targets the bridges are getting.
Also in the 'st.conf' file, you'll need to add a 'tape-config-list='
line (if you haven't done so already) and corresponding data property
line. Unfortunately, I don't have those lines. Unless someone else on
this list have them, I'm guessing you'll need to contact STK for them.
Second, are you running things through a fabric or are you making
direct connections from fiber HBA to the SCSI-FC bridge? If you're using
a fabric, then you'll need to review the info provided by QLogics on
persistent binding. You'll need to bind each bridge to a specific SCSI
target. Unfortunately, there is no way to guarantee that when the system
boots, each bridge will get the same SCSI target each time. Persistent
binding assures this. You'll need this because NBU is *very* sensitive to
the ordering of tapes drivers. I've got a number of L-700's with STK-9840
fiber-based drivers and have learned this all too well. For the binding,
you'll need to edit the 'qla2200.conf' file.
As far as other changes to the 'qla2200.conf' file goes, most of the
default values should be okay. If memory serves me right, any values set
to 'hba0' will be treated as defaults for all other HBAs so there's no
need to duplicate them for each HBA in the system. I've used the STK-3200
SCSI-FC bridge (which is a Crossroads 4200 with [as a STK tech told me] "a
different paint job) and DLT-7000's connected to a Brocade 2800 fibre
switch with a Sun220R and QLA2200's also connected the switch and I used
just the default values. Things worked fine with me. But since you're
As for ACS, I believe that's a StorageTek application, so your STK
sales rep and/or presales engineer should be able to help you there. I
personally haven't had an opportunity to work with the LTO drives but one
of the other engineers here is involved in installing a L-700 with LTO
drives at one of our customer sites and he says (and the STK guys will
hate me saying this) ACS is not needed. They're just treating the drives
as they would a DLT or a 9840 drive. They tell me it works.
-- Tony Guzzi
Sr. Solutions Engineer, AssuredRestore team
Southborough, MA 01772
The Leading Provider of Automated Storage Assurance for the Enterprise
From: Donna Nadimi <donna.nadimi AT lucasfilm DOT com>
To: veritas-bu AT mailman.eng.auburn DOT edu
Date: Wed, 12 Dec 2001 10:34:38 -0800
Subject: [Veritas-bu] Netbackup 3.4/Solaris 2.6/STK L700 LTO
I'm out of my depth here. I'm trying to hook up a STK L700 with 10 LTO
drives to my Sun E450 using QLogic 2200F HBA's. (2 scsi drives per fiber)
I have a couple of questions:
1. What configuration files do I need to edit? What info do I put in
sd.conf? st.conf? qla2200.conf?
2. What is ACS? Where do I get it? What does it do?
If anyone knows the answer to these questions, or has some sort of
documentation telling me what to do, I'd really appreciate you sending it
I've gotten to the point where sgscan can see the changer and 1 drive.
However, I'm not sure which config parameter is making it work.
Thanks in advance.
Your friend in need,
<banging head on keyboard/>
Donna L. Nadimi
UNIX Systems Engineer
donna.nadimi AT lucasfilm DOT com
"UNIX is user friendly. It's just picky about who its friends are."