[Veritas-bu] Which HP/UX driver for robots

                Hi ,

Do you use Veritas Driver for Nt and Win2K ??

We have similar problems , and it disapear when we install Veritas NT&2K
Driver.

HTH

Fabrice

-----Message d'origine-----
De : veritas-bu-admin AT mailman.eng.auburn DOT edu
[mailto:veritas-bu-admin AT mailman.eng.auburn DOT edu]De la part de Boleman,
Jeff
Envoyé : vendredi 6 avril 2001 21:36
À : 'bryan_bahnmiller AT agilent DOT com'; veritas-bu AT mailman.eng.auburn DOT 
edu
Objet : RE: [Veritas-bu] Which HP/UX driver for robots


We run are running 3.4 with patch J0850482. Our Master server is HP-UX 11.0.
Our media servers are a mixture of HP-UX 11.0, HP-UX 10.20, NT 4.0, and
Win2K. We haven't had much problems with 84 errors recently, but had in the
past when on 3.2. Let the group know if this is a problem with that patch.
We were planning on going to it soon.

Jeff Boleman
Systems Administrator III
Andersen Corporation
jboleman AT andersencorp DOT com


-----Original Message-----
From: bryan_bahnmiller AT agilent DOT com [mailto:bryan_bahnmiller AT agilent 
DOT com]
Sent: Friday, April 06, 2001 1:06 PM
To: veritas-bu AT mailman.eng.auburn DOT edu
Subject: RE: [Veritas-bu] Which HP/UX driver for robots


  Well, we did create the sctl driver for the robot. It did not help with
the problem.

  We also have done some additional testing on some separate systems. We
haven't reproduced the HP/UX 11.0 problem. But, we set up a Win2K server
running 3.4. After the J085645 patch it started downing drives (on a
different library and different drives.) We backed out the patch, it stopped
downing drives. I have opened a ticket with Veritas on the problem. I may
fall back to 3.4 with J0850482 on our production UX system and with some
luck maybe that will cure our problem.

    Bryan



> -----Original Message-----
> From: Boleman, Jeff [mailto:jeff.boleman AT andersencorp DOT com]
> Sent: Friday, April 06, 2001 11:40 AM
> To: 'bryan_bahnmiller AT agilent DOT com'; veritas-bu AT mailman.eng.auburn 
> DOT edu
> Subject: RE: [Veritas-bu] Which HP/UX driver for robots
>
>
> You did it right all along, up until the point you upgraded
> to 3.4. In 3.4
> Veritas starts requiring the passthrough drivers.
>
> Jeff Boleman
> Systems Administrator III
> Andersen Corporation
> jboleman AT andersencorp DOT com
>
>
> -----Original Message-----
> From: bryan_bahnmiller AT agilent DOT com
> [mailto:bryan_bahnmiller AT agilent DOT com]
> Sent: Friday, March 30, 2001 4:09 PM
> To: veritas-bu AT mailman.eng.auburn DOT edu
> Subject: [Veritas-bu] Which HP/UX driver for robots
>
>
> All,
>
>   We have been having some issues with downed drives. We are
> running an
> N4000 with HP/UX 11.0 and NetBackup 3.4.1 (3.4 with J0850645
> patch.) We are
> running over LVD SCSI to a Scalar 1000 with IBM LTO drives.
>
>   Tech support claims we should be using the "spt" or "sctl"
> drivers to talk
> to the library. We have always used the "schgr" driver in the
> past, which
> creates the /dev/rac/cXtXdX device. Have we been doing this
> wrong all this
> time?
>
>   Any opinions would be welcome!
>
>
>           Bryan
>
>
> Bryan Bahnmiller
> Agilent Technologies
> (719) 590-3262
> _______________________________________________
> Veritas-bu maillist  -  Veritas-bu AT mailman.eng.auburn DOT edu
> http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu
>
_______________________________________________
Veritas-bu maillist  -  Veritas-bu AT mailman.eng.auburn DOT edu
http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu
_______________________________________________
Veritas-bu maillist  -  Veritas-bu AT mailman.eng.auburn DOT edu
http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu