I don't see a -R option for nsrdmp_recover in 6.1.2 and the man page has no
mention of it.
Usage: nsrndmp_recover [-c client] [-s server] { -r rawdev -S ssid -m mntpnt
| -F }
Is this feature undocumented.
Joel
Terry Lemons wrote:
>
> Hi
>
> One way to do a restore of an NDMP saveset to an alternate location is:
>
> nsrndmp_recover -c {NDMP client} -s {NetWorker Server} -R /vol/vol0/data/etc
> -S {ssid} /vol/vol0/etc
>
> To use 'nsrndmp_recover', you must already know the saveset ID; you can get
> this by using mminfo.
>
> Another way to do it is:
>
> recover -c {NDMP client} -d /vol/vol0/data/etc /vol/vol0/etc
>
> This will allow you to browse through the savesets and select the one you
> want, without needing to know the saveset ID first.
>
> These commands are discussed in the NDMP chapter of the Legato NetWorker
> Administrator's Guide, located on the Legato web site.
>
> Hope this helps!
> tl
>
> Terry Lemons
> CLARiiON Application Solutions Engineering
> EMC²
> where information lives
>
> 4400 Computer Drive, MS D239
> Westboro MA 01580
> Phone: 508 898 7312
> Email: Lemons_Terry AT emc DOT com
>
> -----Original Message-----
> From: Yoon TaeGyoon [mailto:sam AT EFOTEK DOT COM]
> Sent: Monday, September 30, 2002 1:34 AM
> To: NETWORKER AT LISTMAIL.TEMPLE DOT EDU
> Subject: [Networker] NDMP saveset recovery method?
>
> Hi, All.
>
> I'm wondering how to recover NDMP backup saveset...
>
> Backup Server is SUN Solaris 2.7 and Client NetApp F840
>
> I know that 2 method of NDMP recovery
> 1. first, browse recovery : recover or nwrecover
> 2. second, destructive recovery : nsrndmp_recover or nwadmin
>
> How to recover NDMP savesets using GUI or CLI (command line interface) ?
>
> and How to relocate a saveset (ex: /vol/vol0/etc -> /vol/vol0/data/etc)
>
> Please .. Summarize this method....
>
> Please Help me....
>
> I will listen any opition...
>
> Thank you..
>
> PS> what the meaning of below message ? please explain me...
>
> nsrndmp_recover -c mrcoffee.biogen.com -s stampy -S 1839327745 -m
> mrcoffee::/vol/vol4
>
> Starting the recover from the GUI gives the same result.
>
> --
> Note: To sign off this list, send a "signoff" command via email
> to listserv AT listmail.temple DOT edu or visit the list's Web site at
> http://listmail.temple.edu/archives/networker.html where you can
> also view and post messages to the list.
> =*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=
>
> --
> Note: To sign off this list, send a "signoff" command via email
> to listserv AT listmail.temple DOT edu or visit the list's Web site at
> http://listmail.temple.edu/archives/networker.html where you can
> also view and post messages to the list.
> =*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=
--
| Joel Krajden | Room: LB-915, Tel: 848-3052 Fax 848-2830 |
| Senior Systems Analyst | Email: joelk AT cs.concordia DOT ca
|
| Dept. of Computer Science | http://www.cs.concordia.ca/~staffcs/joelk |
| Concordia University | Remember it's a circus and the clowns |
| Montreal, Canada | are supposed to make you laugh, not cry. |
--
Note: To sign off this list, send a "signoff" command via email
to listserv AT listmail.temple DOT edu or visit the list's Web site at
http://listmail.temple.edu/archives/networker.html where you can
also view and post messages to the list.
=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=
|
