[Bacula-users] How to get this autochanger work with bacula
2011-01-19 22:06:18
Hi,
I had a heck of time trying to configure Bacula to work with this Exabyte 1x7
LTO Autoloader.
I wasn't sure which autochanger device /dev/st0 or /dev/nst0. When I do #mt -f
/dev/st0 status and #mt -f /dev/nst0, they all have some good output:
OUTPUT:
SCSI 2 tape drive:
File number=-1, block number=-1, partition=0.
Tape block size 0 bytes. Density code 0x0 (default).
Soft error count since last status=0
General status bits on (50000):
DR_OPEN IM_REP_EN
When I tried to label a volume, I get the error below.
*label
Automatically selected Catalog: MyCatalog
Using Catalog "MyCatalog"
Automatically selected Storage: LTO-2
Enter new Volume name: test
Enter slot (0 or Enter for none):
Defined Pools:
1: Default
2: File
3: Scratch
Select the Pool (1-3): 1
Connecting to Storage daemon LTO-2 at cole:9103 ...
Sending label command for Volume "test" Slot 0 ...
Invalid slot=0 defined in catalog for Volume "" on "LTO-2.0" (/dev/nst0).
Manual load may be required.
3301 Issuing autochanger "loaded? drive 0" command.
3991 Bad autochanger "loaded? drive 0" command: ERR=Child exited with code 127.
Results=/root/bacula/bin/mtx-changer: line 246: mtx: command not found
3910 Unable to open device "LTO-2.0" (/dev/nst0): ERR=dev.c:491 Unable to open
device "LTO-2.0" (/dev/nst0): ERR=No medium found
Label command failed for Volume test.
Do not forget to mount the drive!!!
Below is my -dir.conf configuration
Storage {
Name = LTO-2
Address = cole # N.B. Use a fully qualified name here
SDPort = 9103
Password = "QEPdNZ6gTvOqzAmDEVtiX9J5Xb4PYKKNF0BQm/uISqN+" # password
for Storage daemon
Device = LTO-2 # must be same as Device in Storage daemon
Media Type = LTO-2 # must be same as MediaType in Storage
daemon
Autochanger = yes # enable for autochanger device
Maximum Concurrent Jobs = 6
}
The -sd.conf configuration
Autochanger {
Name = LTO-2
Device = LTO-2.0
Changer Command = "/root/bacula/bin/mtx-changer %c %o %S %a %d"
Changer Device = /dev/sg3
}
Device {
Name = LTO-2.0
Drive Index = 0
Media Type = LTO-2
Archive Device = /dev/st0
AutomaticMount = yes; # when device opened, read it
AlwaysOpen = yes;
RemovableMedia = yes;
RandomAccess = no;
Changer Command = "/root/bacula/bin/mtx-changer %c %o %S %a %d"
Changer Device = /dev/sg0
Alert Command = "sh -c 'tapeinfo -f %c |grep TapeAlert|cat'"
}
Can someone please guide me to the right track?
Thanks
Harry
+----------------------------------------------------------------------
|This was sent by harryl AT zoomedia DOT com via Backup Central.
|Forward SPAM to abuse AT backupcentral DOT com.
+----------------------------------------------------------------------
------------------------------------------------------------------------------
Protect Your Site and Customers from Malware Attacks
Learn about various malware tactics and how to avoid them. Understand
malware threats, the impact they can have on your business, and how you
can protect your company and customers by using code signing.
http://p.sf.net/sfu/oracle-sfdevnl
_______________________________________________
Bacula-users mailing list
Bacula-users AT lists.sourceforge DOT net
https://lists.sourceforge.net/lists/listinfo/bacula-users
|
<Prev in Thread] |
Current Thread |
[Next in Thread>
|
- [Bacula-users] How to get this autochanger work with bacula,
harryl <=
|
|
|