On 7/26/10 12:13 PM, John Drescher wrote:
>snip<
>>>
>>> Did it try to use B0000002 and fail?
>>>
>>> John
>>
>> Both B0000001 and B0000002 are in the changer. I tried loading each of them
>> in the drive, and after each time running the mount command in bacula, but I
>> just keep getting the message that there are no appendable volumes.
>>
> Did you change the status of these volumes after the job started?
>
> John
So, I just tried moving a volume from my scratch pool to my Servers
pool, and pruned it. Bacula marked it purged. I then ran the mount
command, and again I got the message that there are no appendable volumes:
*messages
27-Jul 14:35 billie-sd JobId 1700: Job MailBackup.2010-07-25_01.10.00.28
waiting. Cannot find any appendable volumes.
Please use the "label" command to create a new Volume for:
Storage: "Drive-1" (/dev/st0)
Pool: Servers
Media type: VXA-2
*list volumes pool=Servers
+---------+------------+-----------+---------+-----------------+----------+--------------+---------+------+-----------+-----------+---------------------+
| MediaId | VolumeName | VolStatus | Enabled | VolBytes |
VolFiles | VolRetention | Recycle | Slot | InChanger | MediaType |
LastWritten |
+---------+------------+-----------+---------+-----------------+----------+--------------+---------+------+-----------+-----------+---------------------+
| 8 | A0000007 | Purged | 1 | 123,725,887,488 |
196 | 864,000 | 1 | 7 | 1 | VXA-2 | 2009-06-26
11:10:47 |
| 10 | A0000010 | Full | 1 | 85,035,073,536 |
94 | 2,592,000 | 1 | 9 | 1 | VXA-2 | 2010-07-04
04:21:32 |
| 11 | B0000001 | Recycle | 1 | 1 |
0 | 1,814,400 | 1 | 2 | 1 | VXA-2 | 2010-06-27
06:48:34 |
| 12 | B0000002 | Append | 1 | 0 |
0 | 2,592,000 | 1 | 5 | 1 | VXA-2 | 2010-06-13
05:50:03 |
| 31 | C0000006 | Full | 1 | 71,120,738,304 |
76 | 2,592,000 | 1 | 8 | 1 | VXA-2 | 2010-07-23
16:15:26 |
+---------+------------+-----------+---------+-----------------+----------+--------------+---------+------+-----------+-----------+---------------------+
What the heck could be going on here? I have recently ran into some
weirdnesses with my setup. Everything had been running fine for a long
time, and then when I rebooted the machine, the tape drive showed up on
a different device address. I had to change this, and then it appeared
that suddenly there were some strange problems with my config file,
which I fixed (stuff like it suddenly didn't like upper case letters,
where apparently it didn't care before). But, now I have run a couple of
successful backups since then, until I ran into this weirdness, and I'm
not sure what to do... Using bacula 2.4.4-1 on debian lenny.
------------------------------------------------------------------------------
The Palm PDK Hot Apps Program offers developers who use the
Plug-In Development Kit to bring their C/C++ apps to Palm for a share
of $1 Million in cash or HP Products. Visit us here for more details:
http://ad.doubleclick.net/clk;226879339;13503038;l?
http://clk.atdmt.com/CRS/go/247765532/direct/01/
_______________________________________________
Bacula-users mailing list
Bacula-users AT lists.sourceforge DOT net
https://lists.sourceforge.net/lists/listinfo/bacula-users
|