|
Re: Firewall, amanda client and ports
2007-07-18 12:12:55
Thanks for all replies which highlight that I had not given an
important piece of information: I am using the pre-built binaries as in
amanda-backup_server-2.5.2p1-1.suse10.0.i586.rpm
There was one reply from Jean-Louis Martineau, which looks like
appropriate for my case and I will try that. Other replies relied on
recompiling amanda and if possible I would like to avoid that.
Regards,
Charles
On Wed, 18 Jul 2007 14:15:56 +0200
Charles Stroom <charles AT stremen.xs4all DOT nl> wrote:
> Greetings,
>
> my server (fiume) and my client (stremen) both have a firewall and the
> client fails to be backed up (the server goes fine). amcheck reports
> no problem. On the client, I have opened TCP/UDP port 10080, and TCP
> ports 10082 and 10083, because I seem to have seen something like that
> when googling.
>
> I have also seen that apparently the data connection between server
> and client at the time of the actual backup uses a variety of ports,
> or are looking for free ports, but I do not understand really all
> this. Below are the relevant error messages:
>
>
> Hostname: fiume
> Org : daily_backup
> Config : daily
> Date : July 18, 2007
>
> These dumps were to tape daily-09.
> The next tape Amanda expects to use is: daily-10.
>
> FAILURE AND STRANGE DUMP SUMMARY:
> stremen.localnet / lev 0 FAILED [cannot read header: got 0
> instead of 32768] stremen.localnet / lev 0 FAILED [too many
> dumper retry: "[could not connect DATA stream: can't connect stream
> to stremen.localnet port 22580: Connection timed out]"]
> stremen.localnet / lev 0 FAILED [cannot read header: got 0
> instead of 32768] stremen.localnet /usr lev 0 FAILED [cannot read
> header: got 0 instead of 32768] stremen.localnet /usr lev 0
> FAILED [cannot read header: got 0 instead of 32768]
> stremen.localnet /usr lev 0 FAILED [too many dumper retry:
> "[could not connect DATA stream: can't connect stream to
> stremen.localnet port 12327: Connection timed out]"]
> stremen.localnet /var lev 0 FAILED [cannot read header: got 0
> instead of 32768] stremen.localnet /var lev 0 FAILED [too many
> dumper retry: "[could not connect DATA stream: can't connect stream
> to stremen.localnet port 10731: Connection timed out]"]
> stremen.localnet /var lev 0 FAILED [cannot read header: got 0
> instead of 32768] stremen.localnet /opt lev 0 FAILED [cannot read
> header: got 0 instead of 32768] stremen.localnet /opt lev 0
> FAILED [cannot read header: got 0 instead of 32768]
> stremen.localnet /opt lev 0 FAILED [too many dumper retry:
> "[could not connect DATA stream: can't connect stream to
> stremen.localnet port 8232: Connection timed out]"]
> stremen.localnet /home lev 0 FAILED [cannot read header: got 0
> instead of 32768] stremen.localnet /home lev 0 FAILED [cannot read
> header: got 0 instead of 32768] stremen.localnet /home lev 0
> FAILED [too many dumper retry: "[could not connect DATA stream: can't
> connect stream to stremen.localnet port 21891: Connection timed
> out]"] stremen.localnet /boot lev 0 FAILED [cannot read header:
> got 0 instead of 32768] stremen.localnet /boot lev 0 FAILED [too
> many dumper retry: "[could not connect DATA stream: can't connect
> stream to stremen.localnet port 24997: Connection timed out]"]
> stremen.localnet /boot lev 0 FAILED [cannot read header: got 0
> instead of 32768]
>
>
> STATISTICS:
> Total Full Incr.
> -------- -------- --------
> Estimate Time (hrs:min) 0:02
> Run Time (hrs:min) 0:46
> Dump Time (hrs:min) 0:05 0:02 0:03
> Output Size (meg) 2546.2 1606.8 939.4
> Original Size (meg) 2546.2 1606.8 939.4
> Avg Compressed Size (%) -- -- --
> (level:#disks ...) Filesystems Dumped 9
> 2 7 (1:6 2:1) Avg Dump Rate (k/s) 8428.7
> 11827.1 5651.2
>
> Tape Time (hrs:min) 0:28 0:17 0:12
> Tape Size (meg) 2546.4 1606.8 939.5
> Tape Used (%) 20.7 13.1 7.6
> (level:#disks ...) Filesystems Taped 9
> 2 7 (1:6 2:1)
>
> Chunks Taped 0 0 0
> Avg Tp Write Rate (k/s) 1530.3 1634.8 1379.4
>
> USAGE BY TAPE:
> Label Time Size % Nb Nc
> daily-09 0:28 2607488K 20.7 9 0
>
> [......]
>
> DUMP SUMMARY:
> DUMPER STATS
> TAPER STATS HOSTNAME DISK L ORIG-KB OUT-KB COMP%
> MMM:SS KB/s MMM:SS KB/s --------------------------
> ------------------------------------- -------------
> fiume.localn / 1 3670 3680 -- 0:04 832.2
> 0:04 887.1 fiume.localn /boot 1 10 32 --
> 0:00 666.2 0:01 24.1 fiume.localn /home 2 928560
> 928576 -- 1:36 9640.8 11:15 1375.9 fiume.localn -s/pictures
> 1 870 896 -- 0:06 139.1 0:02 554.9
> fiume.localn /local 1 10 32 -- 0:05 2.0
> 0:01 24.1 fiume.localn /opt 0 1135990 1136000 -- 1:39
> 11467.0 11:31 1644.7 fiume.localn /usr 1 28480 28480
> -- 0:57 503.2 0:13 2231.8 fiume.localn /usr/local 1
> 360 384 -- 0:02 225.7 0:01 268.6
> fiume.localn /var 0 509400 509408 -- 0:40 12717.5
> 5:16 1613.2 stremen.loca / 0 FAILED
> -------------------------------------------- stremen.loca /boot
> 0 FAILED --------------------------------------------
> stremen.loca /home 0 FAILED
> -------------------------------------------- stremen.loca /opt
> 0 FAILED --------------------------------------------
> stremen.loca /usr 0 FAILED
> -------------------------------------------- stremen.loca /var
> 0 FAILED --------------------------------------------
>
> (brought to you by Amanda version 2.5.2p1)
>
> It looks as if everytime another port is used, but is this TCP or UDP?
> Can somebody tell me what I have to tell the firewall (on opensuse
> 10.2), so that it all works?
>
> Regards,
>
>
--
Charles Stroom
email: charles at no-spam.stremen.xs4all.nl (remove the "no-spam.")
|
| <Prev in Thread] |
Current Thread |
[Next in Thread> |
|
Re: Firewall, amanda client and ports,
Charles Stroom <=
|
|
|
