[ADSM-L] 答复: [ADSM-L] backup stgpool - command issue

2012-05-17 20:53:10
Subject: [ADSM-L] 答复: [ADSM-L] backup stgpool - command issue
From: Victor Shum <victorshum AT CADEX.COM DOT HK>
Date: Fri, 18 May 2012 08:42:59 +0800
Dear Rick :

We did not use the DRM now, 

Since the existing tape library slot (48 slot)is not enough to hold all
backup of primary pool; 14 version of user data (each version require 4 to 6
LTO5).  So we try to implement the backup like;

1.  daily schedule backup data to primary pool (daily selective / full
2.  backup stgpool to copypool 
3.  backup TSM DB 
4.  checkout all tape in the library
5.  check in new tape in the library 
6.  checking any expired tape recycle the daily job

the copypool' tape will be transport to DR site, while the primary pool tape
will be store at the safe and reuse for after 14 day

We think we just daily duplicate the primary pool to copypool (using backup
stgpool), and check out all active tape.  Manually trace when the tape shall
be expire; then reuse (cycle) those tape again to make the things work...

So if we need to have the data retention period of 14 but don't have enough
tape slot in the tape library to hold all primary pool tape media.  We have
no way out !!

OR Shall we just shorter the retention period like: from 14 to 10 day, so
that the tape library can hold all the tape inside.  Use DRM to generate and
manage offsite tape form us ??

Best regards,
Victor Shum

发件人: ADSM: Dist Stor Manager [mailto:ADSM-L AT VM.MARIST DOT EDU] 代表 Rick
发送时间: 2012年5月17日 21:10
主题: Re: [ADSM-L] backup stgpool - command issue


Assuming it is a copy pool volume (since primary storage volumes should
always be available in your library).
Investigate the volume status on your TSM server:
Use the "query drmedia" command determine the volume's current state, if in
fact it should be out of the library it's state would be either "offsite,
courier, vault, etc.". This tells TSM that the volume should not be in the
library and do not attempt to mount it. 
If the volume's state is "mountable" then the TSM server thinks the volume
is in the library. Use the "move drmedia" command to apply the correct
status to the volume. 

Additionally, check the access status of the volume by using the query
volume command to make sure it is still readwrite, and not readonly or
unavailable, as the server could have altered its access status when it was
unable to use it.

For a complete explanation of the DRM process refer to the admin guide.

Jax, FL.

-----Original Message-----
From: ADSM: Dist Stor Manager [mailto:ADSM-L AT VM.MARIST DOT EDU] On Behalf Of
Victor Shum
Sent: Thursday, May 17, 2012 7:13 AM
Subject: [ADSM-L] backup stgpool - command issue

Dear all :

Due to tape library slot limitation, we implement TSM 6.3 with the following
scenarios :


TS-3200 with 4 x LTO5, 48 slots

TSM configure

3 x primary pool ( A, B, C) for 1 x copy pool (for offsite - off_data)

4 cycle x 7 day of tape media

Daily backup : 4 ~ 8TB


1.       Different hosts running different backup job, so that all the
Drive will be occupy during the daily backup.

2.       At the end of day, we use backup stgpool to make a copy of
primary pool

3.       Check out all tape (current cycle)

4.       Insert a new set of tape

5.       Audit tape library, check in tape..etc

6.       Repeat 1

But we found the backup stgpool cannot be completed last-night.  From the
actlog, it keep report : ANR1228I Removable volume AAA208L5 is required for
storage pool backup. (SESSION: 10245, PROCESS: 199).  While this media was
used for backup in previous cycle (2 weeks ago).

So I am thinking is some of the files has been deleted on the hosts side
yesterday, so the existing tape (inside the tape library) does not content
those files.  But the "backup stgpool" has to copy all "active" files to the
copy-pool; that is why TSM try to mount other tape has the files on it??
Or I just hit a bug of TSM ??

Best regards,

Victor Shum