Just an update...


I had already tried auditing the library with checklabel=barcode for a
first fix attempt and still saw the error.    Yesterday afternoon working
with ADIC tech support we ran an "inventory process from the library side"
and then reran the audit on  TSM  server checklabel=barcode....and no
errors after that.   (fingers crossed)





Nancy Backhaus
Enterprise Systems
HealthNow, NY
716-887-7979




Zoltan Forray/AC/VCU <zforray AT VCU DOT EDU>
Sent by: "ADSM: Dist Stor Manager" <ADSM-L AT VM.MARIST DOT EDU>
04/10/2006 04:39 PM
Please respond to "ADSM: Dist Stor Manager"


        To:     ADSM-L AT VM.MARIST DOT EDU
        cc:
        Subject:        Re: ANR8300E - I/O error on library desc= the 
destination slot or drive
was full in an attemt to move a volume


Been there - Done that.  Seen it numerous times.

Just perform an audit of your library, scanning the barcodes.  There is an
out-of-sync problem in the library inventory (internal).  There is a tape
who's barcode it didn't read during the last scan pass or you had some
kind of library error.

In fact, I just did one......................................... AUDIT
LIBR <insert your library name here> checkl=b




Nancy L Backhaus <Backhaus.Nancy AT HEALTHNOW DOT ORG>
Sent by: "ADSM: Dist Stor Manager" <ADSM-L AT VM.MARIST DOT EDU>
04/10/2006 03:15 PM
Please respond to
"ADSM: Dist Stor Manager" <ADSM-L AT VM.MARIST DOT EDU>


To
ADSM-L AT VM.MARIST DOT EDU
cc

Subject
[ADSM-L] ANR8300E - I/O error on library desc= the destination slot or
drive was full in an attemt to move a volume






Anyone see this error below?   Looking for direction/suggestions?

The tape(s) do actually does dismount.  The issue is occurring on
different drives.   All volumes are online, no unavail, no damaged, etc. I
audited the library, it was a successful audit checklabel=barcode.

**Background - Updated a week ago Library firmware from 3.1 to 4.1 and
then backed out the library firmware code because internal barcode on the
tapes could not be read.  So we went back to our 3.1 firmware and thought
we were ok again.   Also, a couple other ADIC clients reported similiar
issues with new firmware.   Then we started seeing this error today with
TSM sense data.

Errpt - showing nothing

Only TSM is reporting error, the library and aix are reporting no errors.


Version:
TSM Version - 5.3.2.2
AIX - 5.3 Mod 3
ADIC I2000 Scalar Library(LTO 2 drives), LTO2 tapes



actlog:

04/10/06   13:16:44      ANR8300E I/O error on library BLUE (OP=00006C03,
CC=315,
                          KEY=05, ASC=3B, ASCQ=0D,
SENSE=70.00.05.00.00.00.00.0A.0-
                          0.00.00.00.3B.0D.00.CF.00.06., Description=The

                          destination slot or drive was full in an attempt
to move
                          a volume).  Refer to Appendix D in the
'Messages' manual
                          for recommended action. (PROCESS: 302)
04/10/06   13:16:44      ANR8469E Dismount of LTO volume TS1430 from drive
DRIVE13
                          (/dev/rmt13) in library BLUE01 failed. (PROCESS:
302)


Sense Data=
 Key (05) = illegal request
CC(315)= dest slot was full
ASC=3B, ASCQ=OD = medium destination element is full





Nancy Backhaus
Enterprise Systems
HealthNow, NY
716-887-7979

CONFIDENTIALITY NOTICE: This email message and any attachments are for the
sole use of the intended recipient(s) and may contain proprietary,
confidential, trade secret or privileged information.  Any unauthorized
review, use, disclosure or distribution is prohibited and may be a
violation of law.  If you are not the intended recipient or a person
responsible for delivering this message to an intended recipient, please
contact the sender by reply email and destroy all copies of the original
message.