ADSM-L

Re: 3590 Drive Problem

2005-11-30 08:32:42
Subject: Re: 3590 Drive Problem
From: PAC Brion Arnaud <Arnaud.Brion AT PANALPINA DOT COM>
To: ADSM-L AT VM.MARIST DOT EDU
Date: Wed, 30 Nov 2005 14:32:02 +0100
Hi all,

Take a look at this :
http://www-1.ibm.com/support/docview.wss?rs=663&context=SSGSG7&q1=116584
1&uid=swg21165841&loc=en_US&cs=utf-8&lang=en
May be related to your problem ...
HTH.
Cheers. 


Arnaud 

************************************************************************
******
Panalpina Management Ltd., Basle, Switzerland, 
CIT Department Viadukstrasse 42, P.O. Box 4002 Basel/CH
Phone:  +41 (61) 226 11 11, FAX: +41 (61) 226 17 01
Direct: +41 (61) 226 19 78
e-mail: arnaud.brion AT panalpina DOT com
************************************************************************
******

-----Original Message-----
From: ADSM: Dist Stor Manager [mailto:ADSM-L AT VM.MARIST DOT EDU] On Behalf Of
Helder Garcia
Sent: Wednesday, 30 November, 2005 12:17
To: ADSM-L AT VM.MARIST DOT EDU
Subject: Re: 3590 Drive Problem

I have the same problem here. TSM 5.3.2 on AIX 5.3 64bits. Two drives
9840 that were working properly stop functioning suddenly with messages

ANR8302E I/O error on drive MYDRIVE (/dev/mt0) with volume XXXXXX
(OP=WRITE, Error Number=5, CC=205, KEY=FF, ASC=FF, ASCQ=FF,
SENSE=**NONE**, Description=SCSI adapter failure).  Refer to Appendix D
in the 'Messages'
manual for recommended action.
ANR1411W Access mode for volume XXXXXX now set to "read-only" due to
write error.
ANR0515I Process 1 closed volume XXXXXX.


After that, I tried removing the definitions, remove and rediscover the
devices using smitty. The discover works fine and recreate the device
mt0, but when I try to define the path to it on TSM I got the message

tsm: SERVER>def path SERVER MYDRIVE srctype=server desttype=drive
library=silo device=/dev/mt0 ANR8420E DEFINE PATH: An I/O error occurred
while accessing drive MYDRIVE.
ANS8001I Return code 15.

I'm using ACSLS library and the drives are connected via fiber (switch).

So Gerald, if you get some resolution to your problem, please share it
here :) I'll do the same.

Thanks.

On 11/29/05, Bob Booth - UIUC <booth AT uiuc DOT edu> wrote:
> On Tue, Nov 29, 2005 at 05:27:10PM -0800, Gerald wrote:
> > I have a drive that from AIX lists as available. In TSM when i try 
> > to
> >
> > define a path to the drive I get an "ANR8420E DEFINE PATH: An I/O
> >
> > error occured while accessing drive DRIVE1." and a "ANS8001I Return
> >
> > code 15.". Then below is what appears in the AIX error report.
>
> Has this drive ever worked?  If it has been de-cabled, or the lead 
> drive has been removed, check the cables again.  Make very sure that 
> NONE of the pins are crossed over.  If any of the ground lines are 
> crossed, or not making contact, the drive may register (become 
> available), but you won't be able to do anything with it.  Check the 
> terminators as well, and any place where the cable may have been 
> disconnected.  Those cables are very easy to bend pins on!
>
> If it was functioning and quit, and has not been disconnected, you may

> have a problem in the interface card pack on the drive.  Also make 
> sure that the interface you are connected to on the drive says it is 
> online on the front panel.  You can also rmdev the drive and do a 
> mkdev on it to see if it comes back.
>
> If all else fails, have your CE run a SCSI wrap test after running 
> card diags on the drive.
>
> just some thoughts.
>
> bob
>


--
Helder Garcia

<Prev in Thread] Current Thread [Next in Thread>