ADSM-L

Re: Adding 3592's to a 3494

2004-10-27 17:22:46
Subject: Re: Adding 3592's to a 3494
From: CORP Rick Willmore <RWillmore AT RSAC DOT COM>
To: ADSM-L AT VM.MARIST DOT EDU
Date: Wed, 27 Oct 2004 14:22:16 -0700
Ben,
I will answer this question according to my knowledge of SANs which I am sure 
someone on this list is much more adapt than myself.  I like soft zoning 
because (AFAIK) hard zoning is on a per port basis.  ie.. port 1 is for zone 
BLAH and port 2 is for a different port.  So the device name (WWN) is not 
associated with the zone rather the port number is. I believe most people have 
adapted soft zoning rather than hard but again I have limited experience and 
none with tape libraries.  If you have a new device with a new WWN you should 
just have to reconfigure the zone on the switch to accept the new device (WWN). 
 I am unfamiliar with the TSM side but if the device name changes on the OS you 
will have to change the path's.  Someone should verify this for you because I 
am just extrapolating from my SAN experience and my limited Fiber Channel 
attached tape libraries (3584)

R.

-----Original Message-----
From: Ben Bullock [mailto:bbullock AT MICRON DOT COM]
Sent: Wednesday, October 27, 2004 1:56 PM
To: ADSM-L AT VM.MARIST DOT EDU
Subject: Re: Adding 3592's to a 3494


        Matthew (and others in the group),

        Just this week we put in our 2 test 3592 drives and started
playing with them. These are sweet. So far they are running a little
over 2X the speed of the 3590E drives, and we have yet to test the
capacity.

         We've been able to test out the alternate pathing, dynamic load
balancing, etc.. It's all through a SAN, so we have tested the zoning,
etc. Failovers work as expected with no interruption to the TSM server
at all. Very nice.
        
        AIX 5.2, TSM 5.2.1.3, Atape 9.0.7.0, atldd 5.5.1.0, 3592 drives,
3490 library.

        All has gone smoothly until we went to simulate a failed drive
where we would swap it out for a new one. It didn't go well, with TSM or
the OS not able to see the new drive correctly. When I tried to 'cfgmgr'
it back in, it gave me these errors:

root:># cfgmgr
Method error (/usr/lib/methods/cfgppa_isa -l ppa0 ):
        0514-038 Error loading kernel extension.
Method error (/etc/methods/cfgtsmdd -l mt0 ):
        0514-051 Device to be configured does not match the physical
                 device at the specified connection location.
Method error (/etc/methods/cfgtsmdd -l mt1 ):
        0514-051 Device to be configured does not match the physical
                 device at the specified connection location.

        I had to remove these 2 "mt" devices to get it to stop erroring.
That's a new one to me...

        I have 2 questions:

        1: During the installation of the tape drives the IBM CE asked
if we wanted "hard" or "soft" addressing. His instructions say to do
HARD, but then his support folks said "soft", what should it be? I'll be
calling this in to IBM, but was curious if anybody here had an answer.

        2: On our switch we are zoning the drives and FC adapters by
WWN. Doing it this way, am I going to have to totally remove and
recreate a drive when I swap it out? (i.e. remove from TSM, the OS,
unzone the switch. Replace drive, re-configure it all back in.).

Thanks,
Ben



-----Original Message-----
From: ADSM: Dist Stor Manager [mailto:ADSM-L AT VM.MARIST DOT EDU] On Behalf Of
Matthew Glanville
Sent: Thursday, September 30, 2004 11:34 AM
To: ADSM-L AT VM.MARIST DOT EDU
Subject: Re: Adding 3592's to a 3494


When we upgraded we needed a new library defined in TSM to use the
3592's with different private/scratch categories, and device class's,
drives, etc.. Not a different 'logical' library defined on the 3494
library manager. That may have worked too, but it depends on how
particular you want to be as to which drives/slots are available to each
host connected to the library.

3592's have been good.   So far after 9 months use of 500 tapes and 6
drives.
2 tapes had I/O problems, no serious problem in data lost,  TSM's
'restore volume' cleaned it up in minutes. some drives have just needed
code upgrades to remove minor problems. One had 'clean me' displayed
permanantly, it went way after that. One was replaced, but it was bad
from the factory on initial installation.

Try to do the code upgrades for the drives from the Host's fiber/scsi.
When the IBM SE pushed it via the Library manager it took hours instead
of minutes.

The web interface on the upgraded library manager is great!
No longer do you have to login to the library manager console to find
out why 'operator intervention' is required... You can check it from
your desk and decide to call in IBM to fix the problem or just unload
the tapes that wanted to come out of the I/O slots.

My biggest issue is that the server we have connected to those 6 drives
can't push data fast enough to them, they can go much faster!

Matthew Glanville
Eastman Kodak

<Prev in Thread] Current Thread [Next in Thread>