I use ERD Commander to manipulate/change the boot.ini file after the
restore has been completed on the W2K server.
Regards,
Michael Swinhoe
Storage Management Group
Zurich Financial Services
E-mail: mailto:Mike.Swinhoe AT UK.Zurich DOT com
"Adams, Matt
(US - To: ADSM-L AT VM.MARIST DOT EDU
Hermitage)" cc:
<maadams@DELO Subject: Re: Suggestions for W2K
recovery
ITTE.COM>
Sent by:
"ADSM: Dist
Stor Manager"
<ADSM-L AT VM DOT MA
RIST.EDU>
04/09/2003
04:21
Please
respond to
"ADSM: Dist
Stor Manager"
Thanks for the reply, and your right it is not boot.ini But there has got
to be a way around this. I did another test using ntbackup to restore the
registry instead of TSM.
The boot problem did not return. I have a dump of the registy both pre and
post restore. I hope I can get MS or Tivoli to look at.
-----Original Message-----
From: Christian Svensson [mailto:christian.svensson AT CRISTIE DOT SE]
Sent: Wednesday, September 03, 2003 5:14 PM
To: ADSM-L AT VM.MARIST DOT EDU
Subject: Sv: Suggestions for W2K recovery
Hi Matt!
There is no problem with your boot.ini file.
The problem is the Windows Registry.
The boot device drivers in the registry point on one driver and the new
Server use a newer or another driver to boot up your disk controller card.
When you restore your files/images to a new hardware you need to be sure
that the drivers who installed on the orginal machine is the same as new
new
one.
There is only one way to sold your problem right now.
That is to install the new drivers on the orginal machine and then backit
up
and restore it to the new machine.
But we have a group at Cristie Data Products who looking to sold this kind
of problem when you clone system or run a Disaster Recovery on new
hardware.
Good luck
Christian
============================================================
Från: "Adams, Matt (US - Hermitage)" <maadams AT DELOITTE DOT COM>
Datum: 2003/09/03 Wed PM 04:52:42 CEST
Till: ADSM-L AT VM.MARIST DOT EDU
Ämne: Suggestions for W2K recovery
All,
I am looking for some suggestions on the best way to handle a W2K recovery
to different hardware. It is not so much the different hardware I am
battling, it is boot.ini. I am trying to find out at what point boot.ini
gets put into place from the restored server.
The current (old) server has the Compaq boot partition therefore the
boot.ini looks like this:
[boot loader]
timeout=5
default=multi(0)disk(0)rdisk(0)partition(2)\WINNT
[operating systems]
multi(0)disk(0)rdisk(0)partition(2)\WINNT="Microsoft Windows 2000 Server"
/fastdetect
C:\CMDCONS\BOOTSECT.DAT="Microsoft Windows 2000 Recovery Console" /cmdcons
The new server will not have that seperate Compaq/HP boot partition and
should look like this:
[boot loader]
timeout=5
default=multi(0)disk(0)rdisk(0)partition(1)\WINNT
[operating systems]
multi(0)disk(0)rdisk(0)partition(1)\WINNT="Microsoft Windows 2000 Server"
/fastdetect
I checked boot.ini both before and after the C: and System State restores.
It remained the same, so I am assuming that at some point during the boot
is
when the old boot.ini gets put into place and causes the new server to come
up with a BSOD for "Inaccessable Boot Device"
Thoughts or suggestions?
Regards,
Matt
This message (including any attachments) contains confidential information
intended for a specific individual and purpose, and is protected by law.
If
you are not the intended recipient, you should delete this message. Any
disclosure, copying, or distribution of this message, or the taking of any
action based on it, is strictly prohibited.
============================================================
This message (including any attachments) contains confidential information
intended for a specific individual and purpose, and is protected by law.
If
you are not the intended recipient, you should delete this message. Any
disclosure, copying, or distribution of this message, or the taking of any
action based on it, is strictly prohibited.
___________________________________________________________________________
The information contained in this message is confidential and may be
legally privileged. If you are not the intended recipient, please do not
read, copy or otherwise use it and do not disclose it to anyone else.
Please notify the sender of the delivery error and then delete the
message from your system.
Any views or opinions expressed in this email are those of the author only.
Communications will be monitored regularly to improve our service and for
security and regulatory purposes.
Thank you for your assistance.
___________________________________________________________________________
|