So far,
I've got NT cluster backup going and not the web client and TDP for SQL. I'd 
certainly look into the log files and find out more.

Thanks
--

On Mon, 3 Feb 2003 10:47:45
 Kamp, Bruce wrote:
>I found the dsmerror.log to be a lot more helpful!
>Are you using CAD mode (client acceptor starts the scheduler and/or
>webclient)?
>Also is this cluster running either TDP SQL or Exchange?  If so check the
>port numbers!
>I set my SQL cluster this way:
>Baclient for local disk on 1581
>TDP SQL on 1582
>Cluster resources on 1583.
>
>--------------------------------------
>Bruce Kamp
>Midrange Systems Analyst II
>Memorial Healthcare System
>E: bkamp AT mhs DOT net
>P: (954) 987-2020 x4597
>F: (954) 985-1404
>---------------------------------------
>
>
>-----Original Message-----
>From: prasanna S ghanekar [mailto:gpresy AT lycos DOT com]
>Sent: Monday, February 03, 2003 10:39 AM
>To: Kamp, Bruce
>Subject: RE: WEB Client install fails on NT cluster server
>
>
>It is for a cluster resource and I have specified a different HTTPPORT in
>the options files, which it picks up at the time of installation. For some
>reason, I did not look much in the nt event logs.
>
>Thanks
>--
>
>On Mon, 3 Feb 2003 07:11:49
> Kamp, Bruce wrote:
>>Where there any errors in the dsmerror.log?
>>Is this for a cluster resource?  If so did you specify a different
>>httport?
>>
>>
>>--------------------------------------
>>Bruce Kamp
>>Midrange Systems Analyst II
>>Memorial Healthcare System
>>E: bkamp AT mhs DOT net
>>P: (954) 987-2020 x4597
>>F: (954) 985-1404
>>---------------------------------------
>>
>>
>>-----Original Message-----
>>From: prasanna S ghanekar [mailto:gpresy AT LYCOS DOT COM]
>>Sent: Sunday, February 02, 2003 11:29 PM
>>To: ADSM-L AT VM.MARIST DOT EDU
>>Subject: WEB Client install fails on NT cluster server
>>
>>
>>Folks,
>>
>>Based on the Expert advice, I followed all instructions to configure
>>and setup TSM Backup client for NT cluster server.Then, I moved on to
>>setup Web client in Cluster environment. As the manual says, I used
>>"DSMCUTIL" to install services and not the setup wizard. Also, I was
>>cautious in looking at the Group and Node ownership on the cluster
>>while installing these services.
>>
>>Here is what happens,
>>
>>DSMCUTIL installed services on both nodes but when you try to start
>>those, I get "incorrect parameter" and the services do not start.
>>
>>Is there any workaround ? I did test the backups for physical nodes and
>>cluster node using scheduler service and it went fine.
>>
>>Any help is greatly appreciated..
>>
>>Thanks,
>>
>>Prasanna Ghanekar
>>EDS GMTG MI
>>
>>
>>_____________________________________________________________
>>Get 25MB, POP3, Spam Filtering with LYCOS MAIL PLUS for $19.95/year.
>>http://login.mail.lycos.com/brandPage.shtml?pageId=plus&ref=lmtplus
>>
>
>
>_____________________________________________________________
>Get 25MB, POP3, Spam Filtering with LYCOS MAIL PLUS for $19.95/year.
>http://login.mail.lycos.com/brandPage.shtml?pageId=plus&ref=lmtplus
>


_____________________________________________________________
Get 25MB, POP3, Spam Filtering with LYCOS MAIL PLUS for $19.95/year.
http://login.mail.lycos.com/brandPage.shtml?pageId=plus&ref=lmtplus