Re: Dr. Watson in NT after installing TSM4.1

Whoops....I meant NT4 SP6a

> -----Original Message-----
> From: bbullock [SMTP:bbullock AT MICRON DOT COM]
> Sent: Wednesday, April 18, 2001 3:18 PM
> To:   ADSM-L AT VM.MARIST DOT EDU
> Subject:      Re: Dr. Watson in NT after installing TSM4.1
>
>         Are you getting this pkthread error on NT servers?
>
> Ben Bullock
> Unix system manager
> Micron Technology Inc.
>
>
> > -----Original Message-----
> > From: LeBlanc, Patricia [mailto:Patricia.Leblanc AT LIBERTYMUTUAL DOT COM]
> > Sent: Wednesday, April 18, 2001 1:04 PM
> > To: ADSM-L AT VM.MARIST DOT EDU
> > Subject: Re: Dr. Watson in NT after installing TSM4.1
> >
> >
> > Has anyone seen a pkthread error?
> > We've upgraded from 3.1 to TSM 4.1.1.0 and keep getting this
> > error that
> > hangs the server.  It's not running and it's not down
> > completely.  If it
> > were down, our monitoring would pick that up.
> >
> > 7 servers have been upgraded, but only a couple are having
> > this problem on a
> > regular basis.
> > Any thoughts would be greatly appreciated.
> >
> > > -----Original Message-----
> > > From: Miller, Ryan [SMTP:Miller.Ryan AT PRINCIPAL DOT COM]
> > > Sent: Thursday, April 12, 2001 3:33 PM
> > > To:   ADSM-L AT VM.MARIST DOT EDU
> > > Subject:      Re: Dr. Watson in NT after installing TSM4.1
> > >
> > > The one I can remember off the top of my head is the
> > Fstypes option, it is
> > > no longer supported and if it is in the OPT file, it will
> > cause Dr Watson.
> > > I believe we had another non supported option cause the
> > same problem, but
> > > I can't remember it.  Sorry.  I would review any OPT file
> > you are going to
> > > copy and question any options that seam out of place.
> > That's how we found
> > > ours.
> > >
> > > -----Original Message-----
> > > From: LeBlanc, Patricia [mailto:Patricia.Leblanc AT LIBERTYMUTUAL DOT COM]
> > > Sent: Thursday, April 12, 2001 2:21 PM
> > > To: ADSM-L AT VM.MARIST DOT EDU
> > > Subject: Re: Dr. Watson in NT after installing TSM4.1
> > >
> > >
> > > What are the options you are talking about that are no
> > longer supported??
> > >
> > > > -----Original Message-----
> > > > From: Miller, Ryan [SMTP:Miller.Ryan AT PRINCIPAL DOT COM]
> > > > Sent: Thursday, April 12, 2001 3:13 PM
> > > > To:   ADSM-L AT VM.MARIST DOT EDU
> > > > Subject:      Re: Dr. Watson in NT after installing TSM4.1
> > > >
> > > > Did you use the original OPT file?  If so, there are some
> > options that
> > > can
> > > > cause Dr Watson errors.  They are options that are no
> > longer supported
> > > by
> > > > the newer client, we have experienced this issue also and
> > found this
> > > > cause.
> > > >
> > > > -----Original Message-----
> > > > From: Gottfried Scheckenbach
> > > > [mailto:gottfried.scheckenbach AT xtelligent DOT de]
> > > > Sent: Thursday, April 12, 2001 11:24 AM
> > > > To: ADSM-L AT VM.MARIST DOT EDU
> > > > Subject: Re: Dr. Watson in NT after installing TSM4.1
> > > >
> > > >
> > > > Because there where no answers:
> > > >
> > > > Today I had the same problem - after upgrading a old ADSM
> > 3.1 to TSM 4.1
> > > > installation on NT with SP 3. Just after installation of
> > SP 6 all went
> > > > fine.
> > > >
> > > > Regards,
> > > > Gottfried
> > > >
> > > >
> > > > Shekhar Dhotre wrote:
> > > > >
> > > > > Hi all ,
> > > > >
> > > > > I   installed TSM server 4.1  on WINNT 4.0 service pack
> > 4 , RAM 256 MB
> > > > > whenever i  open configuration wizard   to configure any of the
> > > > parameters in
> > > > > TSM
> > > > > DR. WATSON  shows his face ..  what should i check to
> > correct this
> > > > problem ..
> > > > >
> > > > > Thanks
> > > > > shekhar
> >