Eric,
     What tom is talking about is  the "add lan host" option at the 3494
Library.
One other question, how many nics do you have on the host system, if mor
then one you should define both in the add lan host operation




"Tom Melton" <Tom_Melton AT EMORY DOT ORG>@VM.MARIST.EDU> on 02/20/2001 11:28:06
AM

Please respond to "ADSM: Dist Stor Manager" <ADSM-L AT VM.MARIST DOT EDU>

Sent by:  "ADSM: Dist Stor Manager" <ADSM-L AT VM.MARIST DOT EDU>


To:   ADSM-L AT VM.MARIST DOT EDU
cc:

Subject:  Re: Trying to define a 3494 Library


Try talking to the library from outside ADSM.  Use the mtlib command to
query the library, to get some status info from it.  That will verify
the necessary serial/ethernet connectivity to the library.

I see that you are talking ethernet to the library.  Have you
authorized your ADSM machine access in the library controller.  I think
you have to give the ip address of the ADSM server in the IP setup of
the ATL.

Tom Melton
Emory HealthCare
Emory University

>>> Eric-van.Loon AT KLM DOT NL 02/20/01 11:20AM >>>
Hi *SM-ers!
I am trying to add a 3494 library to our TSM 3.7 server on AIX 4.3.3.
I have performed the following steps:
1) I have installed Atape 5.4.4.0.
2) I have installed atldd 4.1.5.0.
3) I have defined the library in the /etc/ibmatl.conf file by adding
the
following line:
3494-L1  171.21.121.5   3494-L1
4) I used SMIT to configured the LMCP by using the "Add a Tape Drive"
option. I selected the "atl      library LAN/TTY Library Management
Control
Point". I selected the Library Name 3494-L1 which was retrieved from
the
/etc/ibmatl.conf file and it created a lmcp0 with the status defined:
lmcp0 Defined              LAN/TTY Library Management Control Point
5) I used the SMIT option "Configure a Defined Tape Drive" to make the
drive
available. It's now listed as:
lmcp0 Available              LAN/TTY Library Management Control Point
6) I ran CFGMGR which loaded the deamon.
7) I went to TSM to define the library by using the command:
def libr 3494-L1 libt=349x device=/dev/lmcp0
This returns the following error:
ANR8444E Internal Operation: Library 3494-L1 is currently unavailable.
ANR8418E DEFINE LIBRARY: An I/O error occurred while accessing library
3494-L1.
I'm stuck here. Can anybody help me by pointing me to the right place
for
more information? Am I forgetting something?
Thanks in advance for any reply!!
Kindest regards,
Eric van Loon
KLM Royal Dutch Airlines


**********************************************************************
This e-mail and any attachment may contain confidential and privileged
material intended for the addressee only. If you are not the addressee,
you are notified that no part of the e-mail or any attachment may be
disclosed, copied or distributed, and that any other action related to
this e-mail or attachment is strictly prohibited, and may be unlawful.
If you have received this e-mail by error, please notify the sender
immediately by return e-mail, and delete this message. Koninklijke
Luchtvaart Maatschappij NV (KLM), its subsidiaries and/or its employees
shall not be liable for the incorrect or incomplete transmission of this
e-mail or any attachments, nor responsible for any delay in receipt.
**********************************************************************